RF4 RF7050 PRO-FO19 7-50X Trinocular Microscope
₨ 68,000
RF4 RF7050 PRO-FO19 Trinocular Microscope for Phone and PCB Repair
The RF4 RF7050 PRO-FO19 delivers continuous 7X to 50X zoom through a 45-degree inclined, 360-degree swiveling trinocular head. A six-gear mechanical zoom lock lets you return to a set magnification without repeated adjustment. The head and 360-degree adjustable swing arm position the optics over logic boards, BGA packages, and PCB sections without moving the workpiece. A silicone pad and 144 LED ring light complete the bench setup for phone and tablet repair work.
In stock
RF4 RF7050 PRO-FO19 Microscope: Optics and Bench Setup for Board-Level Repair
The RF4 RF7050 PRO-FO19 microscope is built for technicians who spend long sessions inspecting logic boards, reading component markings, and checking solder joints under magnification. Its trinocular head pairs a 10X/22mm wide-field eyepiece with a 0.7X to 5.0X objective, which gives continuous zoom from 7X to 50X. That range covers everything from a full motherboard overview to the pad-level detail you need before an IC change. You get a stable viewing platform with a 32mm column, a 155mm center distance, and a 50mm lifting range, so you can adjust working height without losing focus on the board.
Optical Head and Zoom Range
The head uses a 45-degree inclined design with 360-degree swivel. Your eyes stay in a neutral position when you lean over the bench, and the tube can rotate to share the view with a second technician or a camera. The objective assembly runs from 0.7X to 5.0X and works with the 10X eyepiece to produce the full 7X to 50X span. Optional Barlow lenses at 0.48X, 0.5X, 0.7X, and 2.0X extend the usable range when you need a slightly different working distance. Lower magnification keeps the whole board in view for orientation, while the top end resolves individual SMD resistors and capacitors. Lens aperture measures 76mm, and the eyepiece tubes accept standard 10X/22mm wide-field lenses, so the optics stay comfortable across long diagnostic sessions.
Mechanical Zoom Lock and Swing Arm Movement
The zoom control uses six mechanical gear positions instead of a free-slide focus ring. Each gear locks a fixed magnification, so when you find the right view for a cold joint or a damaged trace, you can return to that exact setting in one movement. This saves time during repetitive inspection, such as comparing a good board against a dead phone with the same zoom. The 360-degree adjustable folding swing arm carries the head across the workspace and lets you reach the far corner of a motherboard without shifting the device. Pressure on the arm stays low, so the head holds its position once you set it. Your workflow stays steady whether you inspect a small tablet board or a larger laptop mainboard.
Lighting, Eyepieces, and Camera Readiness
The 144-LED ring light gives even illumination around the objective, which reduces shadows across pads and pins. Brightness adjusts, so you can soften the light on glossy solder mask and increase it when you work on dark PCB surfaces. The package includes a silicone pad to hold boards steady and protect the surface. A disassembly blade set comes with the kit for opening devices before inspection. For documentation or teaching, the head accepts a 0.5X C-mount adapter. Synchronous zoom keeps the monitor image matched to the eyepiece view, so a second person can follow your work on screen. The camera sells separately, so confirm your chosen sensor and connector before ordering. Anti-light-leakage eyecup design reduces glare that would otherwise wash out fine traces.
Where It Fits on Your Repair Bench
This microscope sits at the inspection stage of most board-level repair workflows. You use it first to check for physical damage, liquid corrosion, and lifted pads before you reach for a multimeter or programmer. After you reflow or replace a component with hot air, the same view confirms that solder joints wet correctly and that adjacent parts did not move. During jumper work, the zoom lets you verify each connection point before you power the board. It also supports the stage between diagnosis and rework, so you can compare a working reference board with a faulty one. If you run a shop that handles both phone and PCB work, one microscope covers charging port inspection, display connector checks, and SMD component identification. Pair it with a hot air station for rework and a multimeter for continuity checks, and the bench works as one system. Upgrading to a higher-end optical head is a logical next step when your repairs demand finer resolution or camera-based documentation.
| Weight | 5.0 kg |
|---|
Key Features
- ✓7X to 50X continuous zoom with 0.7X to 5.0X objective range
- ✓45-degree inclined, 360-degree swiveling trinocular head
- ✓Six-gear mechanical zoom lock for repeatable magnification settings
- ✓360-degree adjustable folding swing arm for wide board coverage
- ✓WF10X/22mm wide-field eyepiece for comfortable viewing
- ✓144-LED ring light for even illumination around the objective
- ✓Synchronous zoom support with 0.5X C-mount adapter
- ✓Silicone pad and disassembly blade set included in the kit
Specifications
| Model | RF7050PRO-FO19 |
|---|---|
| Category | Trinocular Stereo Microscope |
| Technology | 6-gear mechanical zoom lock, synchronous zoom with 0.5X C-mount adapter |
| Compatibility | Universal, not device-specific (for phone, tablet, laptop, and PCB inspection) |
| Magnification | Continuous zoom 7X to 50X |
| Eyepiece | WF10X/22mm |
| Objective | 0.7X to 5.0X |
| Barlow Lens | 0.48X, 0.5X, 0.7X, 2.0X (optional) |
| Column Aperture | Φ32mm |
| Lens Aperture | Φ76mm |
| Center Distance | 155mm |
| Lifting Range | 50mm |
Common Repair Uses
- ✓Verified workflows for board-level repair and inspection.
- ✓Pre-repair visual check for liquid damage, corrosion, and burnt components on a dead phone
- ✓Inspecting lifted or cold solder joints after hot air reflow
- ✓Confirming pad condition before an IC change karna
- ✓Verifying jumper lagana connection points before power-up
- ✓Reading markings on SMD resistors, capacitors, and small ICs
- ✓Checking charging port and display connector pins for bent or lifted contacts
- ✓Comparing a faulty board against a working reference board at the same zoom
- ✓Locating hardware fault areas on logic boards before continuity testing
Compatible Devices
- ✓Universal, not device-specific. Use with any workpiece that fits under the head and swing arm reach.
- ✓Smartphone logic boards, all brands and models, within swing arm reach
- ✓Tablet motherboards and display connector boards
- ✓Laptop mainboards and PCB sections for component inspection
- ✓SMD components, BGA packages, and IC pads for visual inspection
- ✓Charging port and flex connector boards
- ✓Silicone pad surfaces for holding small boards steady during inspection
- ✓Optional 0.5X C-mount camera for screen display (camera sold separately)
- ✓Any stereo-compatible workpiece for general electronics inspection
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What magnification range does this microscope offer?
Can I connect a camera for screen display?
Related products
AY A108 Dot Matrix Battery Truetone Programmer for iPhone
Out of stock
YOUKILOON SAM EDL V2 Cable For Samsung USB EDL Download Mode Cable
In stock



