MT6190W IF IC MediaTek 5G RF Transceiver Chip

₨ 250

MediaTek MT6190W IF IC for 5G Network Repair

The MT6190W IF IC is a MediaTek RF transceiver that converts signals between the RF front end and the baseband modem on MediaTek 5G boards. Teardown analysis confirms this chip inside the Oppo Reno3 5G, built on the AM10822A1 die. When a board shows no service, an unstable signal, or failed network registration after a drop or water damage, this transceiver ranks high on the suspect list. You get the exact MediaTek part number for board-level network repair, suited to technicians who already handle IC changes under a microscope with a hot air station and a matching reballing stencil.

14 People watching this product now!
Description

MT6190W IF IC: MediaTek 5G RF Transceiver for Network Section Repair

The MT6190W IF IC is the RF transceiver MediaTek paired with its early 5G smartphone platforms. In repair shops it is simply called the IF IC. Independent teardown analysis identifies it inside the Oppo Reno3 5G, where the package carries the AM10822A1 die. On a MediaTek 5G board, a failed transceiver produces a network issue that no flash file can fix: the phone shows no service, the IMEI reads correctly while the handset never registers, or the signal drops in and out. Mechanicpk supplies this IC for technicians who work at board level on the network section and need the exact MediaTek part number, not a lookalike from a neighboring series.

What the MediaTek MT6190W RF Transceiver Does on the Board

An RF transceiver sits between the modem inside the SoC and the RF front end, meaning the power amplifiers, filters, antenna switches, and antenna lines. On the receive path, the transceiver takes the incoming radio signal and converts it down to a form the baseband can process. On the transmit path, it takes baseband data and converts it up toward the frequencies the power amplifiers push out to the antenna. Every call, data session, and network registration attempt passes through this stage. A damaged transceiver therefore cuts the phone off from the network entirely or leaves it with weak, unstable reception. The MT6190W belongs to the MediaTek MT61xx transceiver family alongside parts such as the MT6186W and MT6195W, but these chips do not swap with one another. Each matches a specific platform and board layout, so you replace an MT6190W only with an MT6190W.

Diagnosing a Faulty MT6190W IF IC Before Replacement

Rule out the software side first. Check that the baseband version appears, the IMEI reads as valid, and the NV and calibration data remain intact. A null IMEI or corrupted NV region points to a software repair, not an IC change. Next, inspect the network section under a microscope for corrosion, cracked components, or shifted parts near the transceiver, especially on boards that suffered a drop or liquid exposure. Switch your multimeter to diode mode and measure the supply lines and decoupling capacitors around the IC. A line shorted to ground narrows the fault quickly, and a single shorted capacitor sometimes clears the problem without touching the chip. Check the front-end components as well, since a dead power amplifier or antenna switch produces symptoms that look similar. Once the supplies reach the chip and the surrounding parts test good, the MT6190W network IC becomes the confirmed suspect and the replacement makes sense.

Replacement Workflow and Bench Tools

Secure the board in a PCB holder and remove the shield over the network section. Apply a quality flux, then lift the old transceiver with your hot air station at a controlled temperature and airflow so you protect the pads and nearby components. Clean the pads with desoldering wick and your soldering station until they sit flat and bright. Reball the replacement chip with the correct stencil from your reballing kit, align it carefully against the pad markings, and reflow it evenly. Inspect every edge under the microscope for bridging or incomplete joints, clean off flux residue, and reassemble. Finally, test network registration, calling, and mobile data before you return the phone to the customer. If you handle MediaTek 5G boards daily, a bottom preheater makes a logical upgrade: it reduces the heat your hot air has to deliver from above and lowers the risk of lifted pads on multilayer boards.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Genuine MediaTek part number MT6190W for exact-match replacement
  • RF transceiver that handles both the receive and transmit signal paths
  • Teardown-confirmed in the Oppo Reno3 5G
  • Built on the MediaTek AM10822A1 die
  • Restores network registration, calling, and mobile data once you complete the fault isolation
  • Fits standard bench rework with hot air, flux, and a reballing stencil
  • Serves board-level technicians working on the MediaTek 5G network section
  • Supports refurbishing and repair center workflows on MediaTek 5G handsets

Specifications

BrandMediaTek
ModelMT6190W
CategoryMobile Phone ICs > Network & IF ICs
CompatibilityMediaTek 5G smartphone boards designed with the MT6190W transceiver
Supported DevicesOppo Reno3 5G
Technology5G RF transceiver (IF IC), AM10822A1 die

Common Repair Uses

  • No service or no network after water damage on MediaTek 5G boards
  • Weak or dropping signal traced to the transceiver stage
  • Network loss after a drop cracks the transceiver’s solder joints
  • Replacing a burnt or shorted transceiver found during diode-mode testing
  • Recovering the network section after a failed earlier rework
  • Hardware-level network fault where the IMEI and NV data remain intact
  • Mobile data or 5G registration failure confirmed as a hardware fault
  • Board refurbishing where the original transceiver shows physical damage

Compatible Devices

  • Verified scope is the device confirmed by teardown, plus any board whose original IC carries the MT6190W marking.
  • Oppo Reno3 5G
  • MediaTek 5G boards that originally use the MT6190W transceiver
  • Any board where the original IC marking reads MT6190W exactly
  • Not a substitute for MT6186W, MT6195W, or MT6190MV, which carry different part numbers

FAQ

What is the product name?
The product name is MT6190W IF IC.
What is the brand of this product?
The brand of this product is MediaTek.
What is the model of this product?
The model of this product is MT6190W.
What is this product used for?
This product is used for replacing a faulty RF transceiver in the network section of MediaTek 5G smartphone boards.
Which devices are compatible with this product?
This product is compatible with the Oppo Reno3 5G and other MediaTek 5G boards that originally use the MT6190W transceiver.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can I use the MT6190MV or MT6195W in place of the MT6190W?
No. These chips carry different part numbers and match different boards, so replace the MT6190W only with an IC marked MT6190W.
Will changing the MT6190W IF IC fix an IMEI null problem?
No. A null IMEI or corrupted NV data is a software fault. The MT6190W handles the RF signal path, so replace it only when the IMEI reads correctly and hardware testing points to the transceiver.