PM6350 000 Power ic – Qualcomm PMIC for SM6350 & SM7225

₨ 250

PM6350 000 Power ic – Qualcomm Power Management IC

The PM6350 000 Power ic is the main Qualcomm power management IC that pairs with the SM6350 (Snapdragon 690) and SM7225 (Snapdragon 750G) platforms. This PM6350 power IC drives five SMPS rails and 22 LDO regulators, handles the power key input, and talks to the SoC over the SPMI bus. When it fails, the board shows a dead phone, a rail short, or a boot that never starts. Mechanicpk supplies this replacement PMIC for board-level technicians who have isolated the fault and need the exact part number for a Qualcomm 5G motherboard repair.

16 People watching this product now!
Description

PM6350 000 Power ic: The Core Supply Controller on Snapdragon 690 and 750G Boards

The PM6350 000 Power ic sits next to the application processor on Qualcomm SM6350 and SM7225 motherboards and controls nearly every primary supply rail the board needs to boot. If this PM6350 power IC fails, the phone loses its core voltages and presents as a dead phone with no response to the charger or the power button. Mechanicpk stocks this part for technicians who have already traced the fault to the PMIC and need a correct, part-number-matched replacement for an IC change.

What the PM6350 Power IC Controls on the Motherboard

Qualcomm built the PM6350 to communicate with the SoC over the SPMI bus, and the chip occupies two SPMI slave addresses on the board. Through the RPMh regulator framework, it delivers five switch-mode power supplies (SMPS1 to SMPS5) and twenty-two LDO regulators. These rails feed the CPU clusters, memory interface, storage controller, and many peripheral blocks. The chip integrates a power-on (PON) module that reads the power key and the reset input, a GPIO controller, and on-die thermal monitoring. Because one package manages so many rails, a single internal failure can stop the entire boot sequence.

Fault Symptoms That Point Toward the PMIC

A technician usually suspects this PMIC when a main rail near the chip shows a short, when the DC power supply reads abnormal current the moment you press the power key, or when the PMIC area heats up within seconds. Other patterns include a phone that hangs on logo after liquid damage, random restarts under load, a boot loop that survives a clean flash, and a handset that stays dead after flash because the root cause was a hardware fault rather than software. Measure before you replace anything. Check rail resistance with a multimeter, inspect the surrounding area under a microscope, and rule out a shorted capacitor or inductor before you commit to removing the IC.

Replacement Workflow for the PM6350 Power IC

Lock the board in a PCB holder, apply quality flux, and preheat the board evenly before you lift the old chip with a hot air station. After removal, clean the pads with a soldering station and desoldering wick, then check carefully for lifted or torn pads. Reball the new PM6350 with a matching stencil from a reballing kit, align it against the silkscreen outline, and reflow with controlled airflow so you do not shift nearby passive components. Let the board cool fully, then measure the main rails again before you connect a battery or a test box. A careful sequence here protects both the new IC and the expensive SoC beside it.

After the IC Change: Software-Side Verification

A successful PMIC swap restores power, but some boards still refuse to boot because storage or firmware took damage during the original fault. Move to diagnostics with ISP pinout tools and an eMMC programmer or UFS adapter to read storage health and confirm the firmware state. This split between hardware and software stages keeps your diagnosis clean and stops you from replacing parts that never failed.

Platform Compatibility Scope

Mainline Linux kernel sources document the PM6350 as the PMIC for SM6350 boards, and later kernel changes identify the same chip on the SM7225-based Fairphone 4. Manufacturers build different board designs on the same SoC, so always compare the marking on your faulty chip with “PM6350” before you order. Never fit this IC on a board that carries a different Qualcomm PMIC, even when the processor family looks similar.

Why Technicians Source the PM6350 From Mechanicpk

Mechanicpk lists board-level parts with exact part numbers and an honest compatibility scope, so you order the right PMIC the first time. You also find the full rework chain in one place: hot air stations, soldering stations, reballing kits, microscopes, PCB holders, multimeters, and test boxes. For service centers handling Qualcomm 5G boards across Pakistan, that means fewer wrong orders and faster turnaround on no-power repairs.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Qualcomm PMIC matched to the SM6350 and SM7225 platforms
  • Delivers five SMPS rails for high-current core supplies
  • Provides twenty-two LDO regulators for SoC and peripheral blocks
  • Communicates with the SoC over the SPMI bus using two slave addresses
  • Integrated PON block reads the power key and reset input
  • Built-in GPIO controller and on-die thermal monitoring
  • Direct replacement for a confirmed faulty PM6350-000 chip
  • Suited to BGA reballing and hot air rework workflows

Specifications

BrandQualcomm
ModelPM6350 (marking: PM6350-000)
CategoryPower Management IC (PMIC)
CompatibilityQualcomm SM6350 (Snapdragon 690) and SM7225 (Snapdragon 750G) platforms
Supported DevicesFairphone 4 (SM7225); other SM6350/SM7225 boards fitted with the PM6350
TechnologySPMI-bus PMIC with RPMh regulators — 5 SMPS rails, 22 LDO regulators, integrated PON (power key/reset), GPIO controller, thermal monitoring

Common Repair Uses

  • Dead phone with no power and no charging response
  • Main supply rail short traced to the PMIC
  • PMIC overheating immediately after power-on
  • Boot loop that persists after a clean firmware flash
  • Phone hangs on logo after liquid damage
  • Power key not responding due to PON section failure
  • Random restarts and shutdowns caused by unstable supply rails
  • PMIC IC change during board-level motherboard rework

Compatible Devices

  • Qualcomm SM6350 (Snapdragon 690) motherboards fitted with the PM6350
  • Qualcomm SM7225 (Snapdragon 750G) motherboards fitted with the PM6350
  • Fairphone 4 (SM7225 platform)
  • Any board where the original PMIC carries the "PM6350" marking
  • Snapdragon 690 5G handsets that use PM6350 power architecture (verify marking first)
  • Snapdragon 750G 5G handsets that use PM6350 power architecture (verify marking first)
  • Board-level replacement only; not a universal power IC
  • Not compatible with boards using a different Qualcomm PMIC part number

FAQ

What is the product name?
The product name is PM6350 000 Power ic.
What is the brand of this product?
The brand of this product is Qualcomm.
What is the model of this product?
The model of this product is PM6350, marked as PM6350-000.
What is this product used for?
This product is used for replacing a faulty power management IC on Qualcomm SM6350 and SM7225 motherboards.
Which devices are compatible with this product?
This product is compatible with SM6350 (Snapdragon 690) and SM7225 (Snapdragon 750G) boards that use the PM6350, including the Fairphone 4.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which Snapdragon platforms use the PM6350 power IC?
Linux kernel sources document the PM6350 on SM6350 (Snapdragon 690) boards and on the SM7225 (Snapdragon 750G) Fairphone 4. Always match the marking on your board before replacement.
How many voltage regulators does the PM6350 PMIC provide?
The PM6350 provides five SMPS rails (SMPS1 to SMPS5) and twenty-two LDO regulators, along with a power-on block for the power key and a GPIO controller.