MT6315TP Power IC – MediaTek 4-Phase Buck Converter

₨ 400

MT6315TP/B MediaTek Buck Converter for Power Rail Repair

The MT6315TP/B is a MediaTek 4-phase step-down (buck) converter IC supplied in a 45-ball WLCSP package measuring 2.35 × 3.44 mm. It delivers up to 5A per output across a programmable range of 0.4V to 1.19375V, the low-voltage window that core and SRAM-type rails typically use. Technicians use this part during power rail diagnosis, dead board triage, and board-level replacement after a confirmed rail fault. Check the part marking and rail mapping against your board schematic before removal, and test the replacement under a current-limited supply before final assembly.

14 People watching this product now!
Description

MT6315TP Power IC: 4-Phase Buck Converter Overview

The MT6315TP power IC is a 4-phase buck converter from MediaTek’s MT6315 family. Four step-down converters sit inside a single package, and the chip regulates low-voltage rails on a mobile board. Its output range runs from 0.4V to 1.19375V, and each output carries up to 5A. Because this IC supplies low-voltage rails, a fault here usually shows up as a power problem rather than a software one. That makes it a strong candidate early in any power-rail investigation, before you commit time to software or charging diagnostics.

Electrical Specifications for Rail Diagnosis

The chip provides four regulated outputs, and each one is rated for up to 5A. The input tolerates a maximum of 6V, which covers the intermediate supply rails feeding this regulator on typical boards. Output programming spans 0.4V to 1.19375V, and this window is narrow. A measured rail that drifts outside its expected setting points to a regulation fault or a downstream short rather than normal operation. Operating temperature is specified from -30°C to 85°C. Before you condemn the IC, compare the measured voltage against the setting shown on the board schematic. Run the suspect rail from a current-limited bench supply so a short does not cook adjacent components while you test.

Where This IC Fits in Your Repair Workflow

Start with symptom isolation. A dead board, a no-display fault, or a boot loop often traces back to a shorted power rail. Confirm the short with a current-limited supply and, where available, a thermal camera, then narrow the fault to a specific output before you lift anything. Once a buck output is confirmed as the culprit, plan the removal around that single rail. Verify the upstream supply and the other rails it feeds, because a healthy regulator with a bad input will mislead you. Record the measured rail voltages before and after the repair. Those readings justify the work to the customer and confirm the fix when the board is powered back up.

Package, Reballing and Rework Considerations

The 45-ball WLCSP package measures about 2.35 × 3.44 mm, and the ball spacing leaves little margin for error. Hot air rework works well on this package, but it demands a controlled preheat, steady airflow, and a flux that will not bridge adjacent balls during reflow. A microscope is essential for checking ball alignment before and after reflow, and it helps you catch bridged or lifted balls early. Match the stencil, solder paste, and reflow profile to this package size. Clean flux residue thoroughly before you power the board, since residue under a small package can create leakage paths that look like a new fault.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Four integrated step-down converters in one package
  • Up to 5A per output
  • Programmable output range of 0.4V to 1.19375V
  • Maximum input of 6V
  • Operating temperature from -30°C to 85°C
  • Compact 45-ball WLCSP, 2.35 × 3.44 mm
  • Small footprint suited to dense board layouts
  • Part of the MediaTek MT6315 family design

Specifications

BrandMediaTek
ModelMT6315TP/B
CategoryMobile Phone ICs
CompatibilityMediaTek MT6315 family, chipset-family level
Technology4-phase step-down (buck) converter
Input VoltageUp to 6V (maximum)
Output Voltage0.4V to 1.19375V
Power RatingUp to 5A per output
Dimensions2.35 × 3.44 mm (45-ball WLCSP)
Weight0.01 kg

Common Repair Uses

  • Dead board diagnosis after a suspected power rail short
  • Power rail fault isolation using a current-limited bench supply
  • Thermal-camera-assisted short detection on a regulated output
  • Boot loop investigation traced to a power rail fault
  • Board-level IC replacement after confirmed rail failure
  • Hot air reballing of 45-ball WLCSP packages
  • Power-tree verification against the board schematic
  • Post-repair rail voltage verification before final assembly

Compatible Devices

  • MediaTek MT6315 family, verified at chipset-family level only
  • MediaTek MT6315 family 4-phase buck converter, package-level scope
  • Device-level fitment not verified from manufacturer data
  • Confirm the TP/B part marking against the board before replacement
  • Confirm the rail this output feeds on the target board schematic
  • Match the 45-ball WLCSP footprint to the board pad layout
  • Verify the output setting matches the rail spec before powering up
  • Replace only after confirming the rail fault with a current-limited supply
  • Use hot air reflow with microscope inspection

FAQ

What is the product name?
The product name is MT6315TP Power IC.
What is the brand of this product?
The brand of this product is MediaTek.
What is the model of this product?
The model of this product is MT6315TP/B.
What is this product used for?
This product regulates low-voltage power rails on mobile repair boards.
Which devices are compatible with this product?
This IC is compatible with the MediaTek MT6315 family at chipset-family level. Device-level fitment should be confirmed against the board schematic.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What output voltage range does the MT6315TP support?
The output runs from 0.4V to 1.19375V, with up to 5A per output.
Does this IC need hot air rework and a microscope?
Yes. The 45-ball WLCSP package at 2.35 × 3.44 mm requires hot air reflow with microscope inspection of ball alignment.