338S00819-A1 Camera Power Supply IC for iPhone 14 Series
₨ 600
Camera Power IC for iPhone 14 Series
338S00819-A1 is a camera power supply IC listed for the iPhone 14 series, including the iPhone 14, 14 Plus, 14 Pro and 14 Pro Max. When a rear or front camera stops initialising, the camera power rail is one of the first places a technician checks. This IC suits board-level repair shops that already handle camera faults and have a hot air station, microscope and multimeter on the bench. Confirm the part number against the donor board before ordering, because each iPhone generation uses its own camera power IC.
338S00819-A1 Camera Power IC for iPhone 14 Repair
The 338S00819-A1 camera power IC is a board-level component for the iPhone 14 series camera subsystem. Repair catalogues associate this part number with the iPhone 14, 14 Plus, 14 Pro and 14 Pro Max, so the match has to be checked against the donor board’s marking before installation. For a repair shop, this IC belongs in the camera fault workflow, where the camera power rail is tested before any component is replaced. The sections below cover where the IC fits, how it is handled on the bench, and how to confirm the right part.
Where This IC Fits in the Camera Power Path
Camera power ICs of this type regulate supply rails that feed the camera modules. When one fails, the camera may stop initialising, the preview can go black, or the phone may report a camera error. Check the camera connector rails with the board powered before you lift the chip, because a damaged flex connector or a shorted camera module can produce the same symptoms. Replacing a healthy IC wastes time and risks damaging the pads.
Bench Workflow for Replacement
Remove the IC with a hot air station at a controlled temperature, then clean the pads with flux and wick. Inspect the pads under a microscope for lifted or damaged traces before placing the new part. Apply fresh solder paste or flux, align the IC carefully, and reflow it. Power the board and measure the camera rails again with a multimeter before reassembly to confirm the output is present.
Verifying the Correct Part Before Ordering
Read the printed marking on the donor IC and match it to 338S00819-A1 before you order. The same camera function appears on several iPhone generations under different part numbers, so a visually similar IC can be the wrong one. Confirm that the donor board belongs to the iPhone 14 series. If the marking does not match, check the board model and the part number on the schematic before proceeding.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Camera power supply IC, part number 338S00819-A1
- ✓Listed for the iPhone 14 series
- ✓Suited to hot air board-level replacement
- ✓Requires microscope inspection and reflow for clean installation
- ✓Identify by printed marking before ordering
Specifications
| Model | 338S00819-A1 |
|---|---|
| Category | Mobile Phone Camera Power ICs |
| Compatibility | iPhone 14 series |
| Supported Devices | iPhone 14, iPhone 14 Plus, iPhone 14 Pro, iPhone 14 Pro Max |
| Technology | Camera power supply IC |
Common Repair Uses
- ✓Board-level camera power repair on iPhone 14 series logic boards
- ✓No camera detected or camera fails to initialise
- ✓Black camera preview or camera app errors
- ✓Camera power rail faults after drop or liquid damage
- ✓IC replacement during board-level camera repair
- ✓Pad and trace inspection after hot air removal
Compatible Devices
- ✓iPhone 14 series (device-specific, per catalogue listing)
- ✓iPhone 14
- ✓iPhone 14 Plus
- ✓iPhone 14 Pro
- ✓iPhone 14 Pro Max
FAQ
What is the product name?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Is this IC interchangeable with the iPhone 13 camera IC?
Can a dead camera always be fixed by replacing this IC?
Related products
339S00108 WiFi IC For iPad Air iPad Pro 9.7 Replacement
In stock
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock



