YCS Mr Yang S1-160W Soldering Station, 3 C210 Tips
₨ 23,000
S1-160W Soldering Station for Board-Level Work
The YCS Mr Yang S1-160W soldering station gives your repair bench 160W of maximum power, program-chip temperature control and a 100°C to 450°C working range. This kit pairs the controller with a C210 handle and three C210 tips, so you start soldering the day it arrives. Automatic sleep, temperature compensation and a four-segment memory display keep your settings steady through dead phone jobs, charging port replacements and IC change karna work. The station also accepts C115 and C245 tips, so your tip range grows with your workload. Mechanicpk supplies it to repair shops and service centers across Pakistan.
In stock
Precision Heat Control with the S1-160W Soldering Station
The S1-160W soldering station from YCS, sold under the Mr Yang name, targets technicians who solder every day and need fast heat recovery. A program chip controls tip temperature instead of the traditional AC-voltage method, and the station melts solder in about two seconds. You get 160W of maximum power, a 100°C to 450°C range on 220V mains, and a C210 handle that takes cartridge-style tips. That combination covers most bench work on a dead phone, from a charging issue at a burnt connector to a hardware fault under a shield can.
Program-Chip Temperature Control and Compensation
Traditional stations regulate heat by switching AC voltage, and the tip temperature drops hard when you touch a large ground plane. The S1-160W controls temperature through a program chip instead. The chip compensates automatically while you solder, so the tip holds your set value as you drag solder across a shielded area or flow a joint on a thick ground pad. You set any value from 100°C to 450°C. Lower settings protect flex cable pads and fragile connectors, and higher settings handle lead-free solder and heavy copper on charging boards. Short heat-up time also cuts the dwell time on each joint, which reduces pad lifting on boards you cannot afford to damage.
C210 Soldering Iron Tip Compatibility
This kit ships with a C210 handle and three C210 tips. The C210 family sits at the fine end of the cartridge range, so you reach SMD resistors, capacitors, connector pins and small ICs without bridging neighboring pads. The station also accepts C115 and C245 tips and supports T210, T115 and T245 handles, so you swap cartridges instead of buying a second station. C245 tips carry more thermal mass for ground planes and shield cans. C115 tips serve ultra-fine microsoldering. The T115 and T245 handles are separate purchases, so confirm which handle you need before you order. Keep a spare tip for each job type: a fine tip for microsoldering, and a wider tip for drag soldering and large pads.
Where a 160W Soldering Station Fits in Board-Level Repair
Board-level repair follows a repeatable sequence. You diagnose with a multimeter under a microscope, lift the faulty part with a hot air station, clean the pads, solder the replacement and test the board. The S1-160W handles the cleaning and soldering steps, and it carries the heavier jobs a basic iron struggles with. Use it for jumper lagana on broken tracks, charging IC and connector replacement, battery connector work, and rework on boards that show a display problem or a network issue after a drop. Phones that hang on logo or die after flash often need an eMMC ISP connection next. A fine C210 tip lets you tack thin wires onto ISP test points cleanly, and you move straight to your eMMC programmer without a second soldering tool. When a job needs reballing, you tin the pads with the same iron before you reflow the new IC.
Sleep Mode, Memory Display and Bench Setup
The automatic sleep function cuts heat while you set the iron down, which protects the tip and saves you from repeated manual adjustments. A four-segment memory display holds your frequently used temperatures, so you jump between a gentle setting for connectors and a hotter one for ground pads with one press. The angle-adjustable hibernation bracket lets you position the stand to suit your bench, and the silicone organizer keeps spare tips within reach. The box includes a sponge and clean copper balls, so you can maintain the tip from the first joint. Wipe the tip before and after every job, and tin it before you leave the iron idle, so each tip lasts longer.
Building the Rest of Your Repair Bench
Pair this station with a hot air station for component removal, a microscope for pad inspection, and a multimeter for fault tracing. PCB holders keep the board steady while you work. Reballing kits and ISP pinout tools extend the same workflow into BGA and eMMC jobs, while UFS adapters and test boxes cover newer storage and diagnostic tasks. If your volume grows, step up to the T245 handle and C245 tips on this same station, or move to a higher-capacity unit from our soldering stations range.
| Weight | 2.0 kg |
|---|
Key Features
- ✓Program-chip temperature control for fast, accurate heating
- ✓Melts solder in about two seconds
- ✓160W maximum power output
- ✓100°C to 450°C temperature range
- ✓Automatic temperature compensation during soldering
- ✓Automatic sleep function
- ✓Four-segment memory display
- ✓Accepts C210, C115 and C245 tips, with an angle-adjustable hibernation bracket and silicone tip organizer
Specifications
| Brand | YCS (Mr Yang) |
|---|---|
| Model | S1-160W |
| Category | Soldering Station |
| Compatibility | C210, C115 and C245 soldering iron tips; T210, T115 and T245 handles |
| Supported Devices | Universal soldering tool — not device-specific |
| Technology | Program-chip temperature control with automatic temperature compensation, automatic sleep and four-segment memory display; 100°C–450°C range |
| Input Voltage | AC 220V |
| Power Rating | 160W (Max) |
Common Repair Uses
- ✓Board-level soldering and rework on mobile phone PCBs
- ✓Charging port and charging IC replacement
- ✓Jumper lagana on broken tracks and pads
- ✓Battery connector and FPC connector soldering
- ✓Pad cleaning and tinning before IC placement
- ✓Reballing preparation and BGA pad tinning
- ✓ISP wire soldering on eMMC test points
- ✓Shield can and ground plane rework
- ✓Small SMD component replacement
Compatible Devices
- ✓Universal — not device-specific; the station solders any phone mainboard, so scope depends on the tip you fit
- ✓Samsung mainboards
- ✓Oppo mainboards
- ✓Vivo mainboards
- ✓Infinix mainboards
- ✓Tecno mainboards
- ✓Xiaomi and Realme mainboards
- ✓Huawei mainboards
- ✓iPhone series mainboards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the S1-160W use C245 and C115 tips besides C210?
What temperature range and power does the S1-160W offer?
Related products
Mechanic A210 Max Double Solder Iron – 100W C210 Station
Out of stock


