Yihua YH-907A Iron Handle for 852D+, 936, 937D, 8786D
₨ 1,800
Yihua 907A Iron Handle, 50W 24V
The Yihua 907A iron handle is a 50W, 24V AC replacement handpiece with a ceramic heating element and 5-pin connector. It takes 900M-series tips and reaches a working range of 200–450°C. Swap it onto your Yihua 852D+, 936, 937D, 8786D, 878D or 898D station when the original iron burns out, and you skip the cost of a new station. Check your station model against the compatibility list before ordering, because the 937D+ falls outside it. Keep one on your repair bench for charging port jobs, battery connector work and pad repair.
In stock
Yihua 907A Iron Handle: Direct Heater Replacement for 900M-Series Yihua Stations
The Yihua 907A iron handle replaces the handpiece on Yihua soldering stations that drive a 24V AC, 50W iron with a 900M-series tip. When the original handle on your 852D+, 936, 937D or 8786D station burns out, you keep the station. You swap the handpiece, plug the 5-pin connector back in, and the controller reads the thermal sensor again. A workshop that runs soldering stations all day on charging port jobs, battery connector work and flex cable removal gains the most from a spare 907A on the shelf, because a dead iron stops every other job on the bench.
Electrical and Thermal Profile
The 907A runs on 24V AC and delivers 50W through a ceramic heating element paired with a thermal sensor. Supplier listings quote a working range of 200–450°C, which covers leaded and lead-free solder on phone boards. The sensor loop measures roughly 0.5 ohm on the original-spec handle, so you can check it with a multimeter before you blame the station’s control board. An open-circuit reading on the heater points to a burnt element. A normal reading shifts your diagnosis toward the cable, the connector or the controller. The handle accepts 900M-series tips, so the chisel, conical and bent tips already in your drawer fit without adapters.
Station Compatibility You Should Confirm First
Yihua lists the 907A for the 936, 936B, 937D, 8786D, 898D, 898BD, 878, 878A, 878D, 878AD, 872D, 852, 852D, 852D+ and 862D families, and resellers extend the list to the 853D 1A and 853DA 1A. The 937D+ falls outside the list. Stations from other brands may not match the pin layout. Yihua also sells the 907I and 917D handles for newer connector generations, and those do not interchange with the 907A. Read the code on your old handle and match it to “907A” before you order. That one check saves you a return and a day of downtime.
Where the Handle Fits in Your Repair Workflow
Hot air handles BGA and shield work. The iron handles the jobs hot air cannot do cleanly: tinning pads, replacing charging ports, reattaching battery connectors, jumper lagana on broken traces, and resoldering after an IC change karna. A dead phone that arrives after a failed charging port job often needs only a steady iron and a clean pad. Pair the 907A with a hot air station for chip work, a PCB holder for board stability, a microscope for pad inspection and a multimeter for continuity checks after each joint. Reballing kits and soldering stations from the same catalogue cover the rest of that workflow.
Why Technicians Replace the Handle Instead of the Station
A burnt handle costs a fraction of a complete soldering station, and the swap takes minutes. The 907A uses the common heater design, so the Yihua YH-133A heating element lists the 907A and 907C as compatible replacement cores. You can re-core a handle that still has a sound body and keep a second complete handle ready for the next failure. Stock two on a busy bench and your charging issue and hardware fault repairs never wait on a dead iron.
| Weight | 0.3 kg |
|---|
Key Features
- ✓50W power output on a 24V AC supply
- ✓Ceramic heating element with thermal sensor for stable temperature feedback
- ✓200–450°C working range for leaded and lead-free solder
- ✓Accepts 900M-series tips
- ✓5-pin connector for Yihua 907A-type station sockets
- ✓Replacement heater core available under the YH-133A part code
- ✓Fits a wide range of Yihua 852, 878, 898, 936 and 8786D station families
- ✓Pencil-style handle for fine board work
Specifications
| Brand | Yihua |
|---|---|
| Model | 907A (YH-907A) |
| Category | Soldering Iron Handle / Replacement Handpiece |
| Compatibility | Yihua 936, 936B, 937D (not 937D+), 8786D, 898D, 898BD, 878, 878A, 878D, 878AD, 872D, 852, 852D, 852D+, 862D, 853D 1A, 853DA 1A, 706 |
| Technology | Ceramic heating element with thermal sensor, 5-pin connector, 900M-series tip system, 200–450°C working range |
| Input Voltage | 24V AC |
| Power Rating | 50W |
Common Repair Uses
- ✓Hand soldering on mobile phone boards with 900M-series tips
- ✓Charging port replacement
- ✓Battery connector reattachment
- ✓Pad tinning and pad repair
- ✓Broken trace repair with jumper wire
- ✓Shield can resoldering after IC change
- ✓Flex cable and FPC connector soldering
- ✓Wire soldering on SIM tray and speaker leads
- ✓Replacing a burnt iron on a working station
Compatible Devices
- ✓Yihua soldering and rework stations that use a 24V AC, 50W, 5-pin 907A-type iron (not mobile phone models)
- ✓Yihua 936 and 936B soldering stations
- ✓Yihua 937D soldering station (not 937D+)
- ✓Yihua 8786D soldering and hot air rework station
- ✓Yihua 852D+ and 852D rework stations
- ✓Yihua 878, 878A, 878D and 878AD stations
- ✓Yihua 898D and 898BD stations
- ✓Yihua 872D and 862D stations
- ✓Yihua 853D 1A and 853DA 1A stations
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the Yihua 907A fit the 937D+ station?
Which soldering tips work with the Yihua 907A?
Related products
Aifen 3310 Pro 33V/10A 330W Adjustable DC Power Supply
In stock



