Relife RL-044 XM2 Stencil – MSM8974 Xiaomi BGA Reballing

₨ 599

XM2 Stencil for Xiaomi MSM8974 CPU Reballing

The Relife RL-044 XM2 Stencil is a 0.12 mm steel BGA reballing plate for the MSM8974, MSM8274 and MSM8674 CPU layout in Xiaomi Mi 4 series, Mi 3, Mi 3S and Mi Note boards. Round and square holes guide solder paste or balls onto the CPU pads, so you rebuild a clean ball array after removal. Pair it with your hot air station, microscope and PCB holder to repair a dead phone, a hang on logo fault or a boot loop that traces back to a failed CPU joint. Mechanicpk supplies this Relife XM2 plate to technicians and service centers across Pakistan.

In stock

17 People watching this product now!
Description

Relife RL-044 XM2 Stencil for MSM8974-Family Xiaomi Boards

The Relife RL-044 XM2 Stencil gives you a dedicated 0.12 mm steel template for the MSM8974, MSM8274 and MSM8674 processor footprint used in the Xiaomi Mi 4 series and the Mi 3, Mi 3S and Mi Note boards. XM2 sits inside the XM range of the RL-044 family, where each numbered plate matches one Xiaomi or Redmi CPU layout, so you pick the plate that fits the chip instead of forcing a near match. Mechanicpk supplies XM2 as a single plate, so you add exactly the layout your bench needs without buying a full multi-plate set.

Where XM2 fits in your CPU reballing workflow

A CPU reballing job starts when a hot air station or preheater lifts the processor. You then clean the pads on the board and the chip with flux and solder wick. Next, you seat the XM2 plate over the CPU, align every aperture to its pad under a microscope, and press solder paste or balls through the holes. Keep your airflow low and preheat from below, because a strong stream blows paste off the plate. A controlled heat pass melts the paste into uniform balls, and the plate lifts away from the chip. The stencil covers only the ball-forming step, so you pair it with a stable soldering station and a PCB holder that keeps the board flat. Technicians use this step on a dead phone or a hang on logo fault when a cracked CPU solder joint causes the hardware fault, because fresh balls restore the connection before they reseat the processor.

Build and design points that matter on the bench

Relife cuts the RL-044 series from steel at 0.12 mm thickness, and distributor listings describe the material as resistant to thermal deformation, which matters when your hot air stream hits the plate job after job. The series uses round and square holes, and the XM2 marking on the plate lets you sort a drawer full of stencils by layout in seconds. A flat, rigid plate sits flush against the chip, which limits solder bridging between neighboring balls and keeps ball height consistent across the array. Wipe the plate with isopropyl alcohol after each job and store it flat. A bent plate leaves uneven balls and sends you back to the start of the reballing process.

Matching XM2 to the right Xiaomi board

Check the CPU marking before you pick the plate. XM2 covers the Xiaomi 4 series plus the Mi 3, Mi 3S and Mi Note, all built around MSM8974, MSM8274 or MSM8674. Newer boards need other plates from the XM range: XM1 handles MSM8998 on the Mi 6 series and Mix 2, and XM4 handles MSM8956 and MT6795 on Redmi Note 2, Redmi Note 3 and Mi Max. When a board shows a charging issue or a network issue, test it with a multimeter and a test box before you pull the CPU, so you reball only when the fault points there. If the phone stays dead after reballing, read the storage through an ISP pinout tool or an eMMC programmer. Newer Xiaomi boards with UFS storage need UFS adapters instead. Browse Mechanicpk’s reballing kits, hot air stations, soldering stations, microscopes and PCB holders to complete the bench around this plate.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 0.12 mm steel plate built for repeated hot air exposure
  • Dedicated XM2 layout for MSM8974, MSM8274 and MSM8674 CPUs
  • Round and square holes for paste or ball placement
  • Thermal deformation resistance listed for the RL-044 series
  • Clear XM2 marking for fast sorting inside a stencil drawer
  • Flat, rigid plate that sits flush on the CPU surface
  • Part of the Relife RL-044 XM range for Xiaomi and Redmi layouts
  • Single-plate purchase for a targeted bench upgrade

Specifications

BrandRelife
ModelRL-044 XM2
CategoryBGA Reballing Stencil
CompatibilityXiaomi 4 series, Mi 3 / Mi 3S / Mi Note boards with MSM8974, MSM8274 or MSM8674 CPU
Supported DevicesXiaomi Mi 4 series, Mi 3, Mi 3S, Mi Note
TechnologyBGA tin planting (reballing) steel mesh with round and square holes
MaterialSteel
Thickness0.12 mm

Common Repair Uses

  • CPU-level reballing on Xiaomi MSM8974-family boards
  • CPU reballing after removal with a hot air station
  • Tin planting a new or reclaimed MSM8974, MSM8274 or MSM8674 CPU
  • Reballing a CPU on a dead phone with a suspected failed solder joint
  • Restoring a CPU on a board that hangs on logo
  • Fixing a boot loop that traces back to CPU ball contact
  • Rebuilding balls after a cleaned CPU shows damaged or missing balls
  • Bench practice on Xiaomi 4-series boards for new technicians
  • Keeping a consistent ball array across repeat CPU jobs in a service center

Compatible Devices

  • Xiaomi boards built on the Qualcomm MSM8974 / MSM8274 / MSM8674 CPU family
  • Xiaomi Mi 4 series
  • Xiaomi Mi 3
  • Xiaomi Mi 3S
  • Xiaomi Mi Note
  • Qualcomm MSM8974 CPU
  • Qualcomm MSM8274 CPU
  • Qualcomm MSM8674 CPU

FAQ

What is the product name?
The product name is Relife RL-044 XM2 Stencil.
What is the brand of this product?
The brand of this product is Relife.
What is the model of this product?
The model of this product is RL-044 XM2.
What is this product used for?
This product is used for BGA reballing of MSM8974, MSM8274 and MSM8674 CPUs on Xiaomi boards.
Which devices are compatible with this product?
This product is compatible with the Xiaomi Mi 4 series, Mi 3, Mi 3S and Mi Note boards built on MSM8974, MSM8274 or MSM8674 CPUs.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which CPUs does the Relife RL-044 XM2 stencil support?
XM2 supports the Qualcomm MSM8974, MSM8274 and MSM8674 CPU layout used in Xiaomi 4-series, Mi 3, Mi 3S and Mi Note boards.
Can I use XM2 on a Xiaomi Mi 6 or Redmi Note 5 board?
No. XM2 matches the MSM8974 family only. Mi 6 and Mix 2 boards with MSM8998 use XM1, and Redmi Note 5 and Note 5 Pro boards with Snapdragon 636 or 660 use XM6.