Heat Proof Tape for Mobile Repair and Hot Air Rework
₨ 350
Heat Proof Tape for Mobile Repair Shops in Pakistan
Heat proof tape for mobile repair shields the parts around your rework zone while hot air does its job. You mask flex cables, connectors, plastic frames and neighbouring components before you lift an IC, reflow a BGA or remove a shield can. The tape sticks to the board, holds through repeated heat exposure and peels off when you finish. It belongs on every PCB repair bench that runs a hot air station, whether you handle dead phone motherboards, charging IC replacement or display connector work. Mechanicpk supplies it to technicians who want clean, controlled rework without collateral damage to nearby parts.
In stock
Heat Proof Tape for Mobile Repair: Protect Nearby Parts During Hot Air Rework
Heat proof tape for mobile repair solves a problem every technician meets on the bench: hot air does not stop at the component you target. When you heat a charging IC, a PMIC or an eMMC, the airflow also reaches flex connectors, battery sockets, plastic standoffs and small passives beside it. This tape gives you a barrier you place in seconds, so the heat lands where you aim it. You work faster, you reduce the risk of a hardware fault caused by your own rework, and you protect boards that customers already brought in as a dead phone. Mechanicpk stocks it for repair shops across Pakistan that run daily hot air jobs.
Where heat proof tape fits in your rework workflow
You use this tape at the start of the rework stage, right after diagnostics and before you switch on the hot air station. Once you confirm the faulty IC, you cover the surrounding area, leave only the target footprint exposed and then apply flux and heat. The same step applies to IC change karna on a charging section, reballing a CPU, removing a shield frame or reflowing a loose connector. Heat resistant tape for PCB work also helps during microscope inspection, because a masked board keeps your attention on the repair zone instead of on parts you worry about melting. Pair it with your soldering station, microscope and PCB holder for a complete rework setup.
Masking flex cables, connectors and plastic parts
Flex cables and plastic connectors take the first hit when you work close to the board edge. You lay a strip over the connector body, press it down along the edges and keep the airflow moving over the target IC. On boards with tightly packed components, you cut narrow strips and cover individual passives you cannot afford to shift. Because hot air rework tape stays flat on the PCB surface, it does not lift under airflow the way cheap masking tape does. You also use it to hold a loose flex or a ribbon cable out of the way while you work. Test any new roll on a scrap board first, since heat tolerance changes between tape types and nozzle temperatures.
Bench tips for clean application and removal
Clean the board surface with isopropyl alcohol before you apply the tape, so the adhesive grips firmly. Press the strip down with tweezers, keep the edges tight against the footprint and avoid covering the pads you need to heat. Keep your nozzle moving and hold a safe distance, because no tape replaces good heat control. After rework, peel the strip slowly at a low angle to avoid lifting solder mask or small components. Store the roll away from dust and direct heat, and keep a few pre-cut strips on your bench for quick jobs like boot loop issue repairs and charging issue fixes, where speed matters.
| Weight | 0.9 kg |
|---|
Key Features
- ✓Heat-resistant tape designed for hot air rework
- ✓Shields flex cables, connectors and plastic parts
- ✓Sticks firmly to PCB surfaces during airflow
- ✓Peels off after rework without a heavy mess
- ✓Cuts easily into narrow strips for tight boards
- ✓Suits mobile, tablet and laptop board repair
- ✓Works with hot air stations and soldering setups
- ✓Fits daily repair shop and training lab use
Specifications
| Category | Repair Accessories |
|---|---|
| Compatibility | Universal, not device-specific |
| Supported Devices | Universal use on mobile phone PCBs and other electronic boards |
Common Repair Uses
- ✓Heat protection during hot air rework on mobile PCBs
- ✓Masking flex connectors during IC removal
- ✓Shielding plastic sockets while reflowing a charging port
- ✓Protecting nearby passives during BGA reballing
- ✓Covering display connectors during hot air work
- ✓Holding ribbon cables aside during rework
- ✓Protecting battery connectors during PMIC replacement
- ✓Masking areas during shield can removal
- ✓Securing small parts while you work on a dead phone board
Compatible Devices
- ✓Universal heat shielding accessory, not device-specific
- ✓Android smartphone motherboards
- ✓iPhone logic boards
- ✓Tablet PCBs
- ✓Laptop and notebook motherboards
- ✓Smartwatch boards
- ✓Flex cable and FPC connectors
- ✓Charging and battery connector areas
- ✓Shield can and BGA rework zones



