Relife RL-044 XM1 Stencil – MSM8998 BGA Reballing

₨ 599

Relife RL-044 XM1 MSM8998 Reballing Stencil

The Relife RL-044 XM1 stencil is a 0.12 mm steel reballing mesh built for the Qualcomm MSM8998 (Snapdragon 835) processor. You use it on the Xiaomi Mi 6 series and Mi MIX 2 when a CPU comes off the board and needs a clean, even set of solder balls before it goes back on. Round, full-coverage holes hold the ball pitch, and the thin steel body handles repeated hot air cycles without losing shape. It slots straight into a BGA rework routine next to your hot air station, flux and microscope, so you spend less time chasing bridged or missing balls on a dead phone.

In stock

11 People watching this product now!
Description

Relife RL-044 XM1 Stencil for MSM8998 CPU Reballing

The Relife RL-044 XM1 stencil gives you a ready-made solder ball pattern for the Qualcomm MSM8998 (Snapdragon 835) processor used on the Xiaomi Mi 6 series and the Mi MIX 2. When a CPU lifts, cracks a ball joint or comes off during board repair, you align this steel mesh over the cleaned pads, apply paste or place balls, and reflow a fresh, even array. The XM1 sits in Relife’s RL-044 Xiaomi range and does one job well: it restores clean ball geometry on the MSM8998 package without guesswork.

Where the XM1 Fits in the MSM8998 Repair Workflow

An MSM8998 board usually reaches your bench as a dead phone, a unit that hangs on logo, or a handset stuck in a boot loop issue after a drop. You rule out the battery connector, power lines and storage first with a multimeter and a test box. If those checks come back clean, a lifted or cold CPU joint becomes the main suspect. You then remove the processor with a hot air station, clear the pads with flux and braid under a microscope, and move to reballing. The XM1 covers that step. It does not replace diagnosis. It makes the repair repeatable once your diagnosis points at the CPU. Technicians who handle IC change karna jobs on Xiaomi boards save time because one stencil matches the chipset, and you reuse the same pattern on every Mi 6 and MIX 2 board that comes through your shop.

Stencil Build and Reballing Behavior

Relife cuts the RL-044 range from 0.12 mm steel. That thickness gives you enough height to hold solder balls in place while the mesh stays thin enough to lift off cleanly after reflow. Round, full-coverage holes keep the pitch spacing consistent across the array, so balls land where the CPU pads sit instead of drifting toward their neighbours. The steel resists high heat and repeated use, which matters when you reball several boards in one day.

For the best result, clamp the board in a PCB holder, centre the stencil over the pads, and press it flat before you apply anything. Reflow with controlled hot air, let the stencil cool, and peel it away from the board with steady pressure. Check the finished array under magnification. Every ball should sit round, even and separate from its neighbours. If one ball is missing or two have merged, clean the pads and repeat the process before you place the CPU, because a weak array only shows up as a hang on logo or random reboot after you reassemble the phone.

Pairing the XM1 With the Rest of Your Rework Bench

One stencil does not complete a reballing setup. You still need a stable hot air station for the reflow, a soldering station for pad cleaning, a reballing kit with solder paste or balls, and a PCB holder to keep the board flat. A microscope makes the final inspection reliable. If the board needs software work after the hardware repair, an ISP pinout tool, an eMMC programmer or a UFS adapter finishes the job.

The RL-044 Xiaomi range uses a separate stencil for each chipset family. MSM8953, MSM8996 and SM8150 boards need their own stencils from the range, because XM1 matches the MSM8998 package. A shop that repairs mixed Xiaomi boards usually buys the XM1 as a starting point and adds the other stencils as chipset demand grows. For Pakistani repair shops that see Mi 6 and MIX 2 boards on a regular basis, the XM1 pays for itself the first time it saves a CPU instead of a full board replacement.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Built for the Qualcomm MSM8998 (Snapdragon 835) CPU package
  • 0.12 mm steel mesh thickness
  • Round, full-coverage holes hold ball pitch spacing
  • Precise alignment over the CPU pads
  • Thin body with durable construction
  • Resists high heat and repeated wear
  • Part of the Relife RL-044 Xiaomi stencil range
  • Fits standard BGA reballing workflows with hot air and paste

Specifications

BrandRelife
ModelRL-044 XM1
CategoryBGA Reballing Stencil
CompatibilityQualcomm MSM8998 (Snapdragon 835) CPU
Supported DevicesXiaomi Mi 6 series, Xiaomi Mi MIX 2
TechnologyBGA tin planting steel mesh, 0.12 mm thickness
MaterialStainless steel

Common Repair Uses

  • CPU reballing and tin planting on MSM8998 Xiaomi boards
  • Reballing an MSM8998 CPU after hot air removal
  • Restoring ball geometry on a lifted or cold-jointed CPU
  • Repairing a dead phone after a drop with a suspected CPU joint fault
  • Fixing a hang on logo or boot loop issue traced to the CPU
  • Replacing a CPU during a board-level IC change karna job
  • Re-tinning a CPU that comes from a donor board
  • Training technicians on BGA reballing technique

Compatible Devices

  • Verified scope is the MSM8998 CPU package on Xiaomi Mi 6 series and Mi MIX 2 boards
  • Xiaomi Mi 6 series
  • Xiaomi Mi MIX 2
  • Qualcomm MSM8998 (Snapdragon 835) CPU package

FAQ

What is the product name?
The product name is Relife RL-044 XM1 Stencil.
What is the brand of this product?
The brand of this product is Relife.
What is the model of this product?
The model of this product is RL-044 XM1.
What is this product used for?
This product is used for reballing the Qualcomm MSM8998 CPU on Xiaomi boards after hot air removal.
Which devices are compatible with this product?
This product is compatible with the MSM8998 CPU package on the Xiaomi Mi 6 series and Xiaomi Mi MIX 2.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which CPU does the Relife RL-044 XM1 stencil support?
The XM1 stencil supports the Qualcomm MSM8998 (Snapdragon 835) CPU used on the Xiaomi Mi 6 series and Mi MIX 2.
Can I use the XM1 stencil on a Snapdragon 855 SM8150 board?
No. The XM1 matches the MSM8998 package. SM8150 boards need a different stencil from the RL-044 Xiaomi range, such as the XM10.