Relife RL-044 XM8 Stencil – MSM8996 BGA Reballing
₨ 599
MSM8996 Reballing Stencil for Xiaomi Mi 5 Series
The Relife RL-044 XM8 is a 0.12 mm stainless steel reballing stencil cut for the Qualcomm MSM8996 CPU used in the Xiaomi Mi 5, Mi 5S, Mi 5S Plus, Mi Note 2 and Mi MIX. Round and square apertures help each solder ball form full and even. The thin sheet sits tight on the chip surface and resists heat and metal fatigue, so it stays flat across repeated reflow cycles. Mechanicpk supplies the XM8 to technicians who need a chip-specific template for CPU reballing instead of a universal stencil that never lines up with the pads.
In stock
MSM8996 BGA Reballing Stencil for Xiaomi Mi 5 Boards
The Relife RL-044 XM8 is an MSM8996 BGA reballing stencil built for the Qualcomm CPU inside the Xiaomi Mi 5, Mi 5S, Mi 5S Plus, Mi Note 2 and Mi MIX. You lay the 0.12 mm steel mesh over a cleaned chip, press solder paste through its apertures and reflow a fresh ball array. Relife follows the original factory drawings for each RL-044 stencil, so the aperture layout reflects the real pad map. That precision matters on a dense CPU footprint, where one missing or bridged ball sends you back to a dead phone after hours of bench work.
Steel construction and hole design
The XM8 uses ultra-thin 0.12 mm stainless steel with both round and square apertures. The hole shapes help each solder ball form round and complete, and the thin sheet sits tight against the chip so paste does not creep under the mesh. Relife selects steel with high-temperature resistance and metal fatigue resistance, which keeps the stencil flat through repeated heat cycles instead of warping after a handful of jobs. When you apply paste, hold the stencil flat with tape at the corners, scrape in one direction and lift straight up to avoid smearing. Wipe flux residue off after each use and store the sheet flat so the apertures stay clear.
Where the XM8 fits in an MSM8996 repair
Xiaomi Mi 5 generation boards reach the bench as a dead phone, a boot loop issue or a hang on logo case that can trace back to a hardware fault under the CPU. You lift the chip with a hot air station, clean the pads and the chip underside with flux and braid on a soldering station, and inspect both surfaces under a microscope. The stencil takes over from there. Clamp the CPU in a reballing platform or PCB holder, align the apertures to the pads under magnification, spread paste or place balls, and heat until the balls form. After you reseat the chip, check the power rails with a multimeter for shorts before you power the board. Faults that come from software or storage rather than solder joints belong on a different path, so test boxes, ISP pinout tools, eMMC programmers and UFS adapters cover the flashing side. Decide between the hardware route and the software route before you pull the CPU.
Choosing the right stencil from the RL-044 Xiaomi range
Relife numbers its Xiaomi stencils by platform. XM8 covers MSM8996. XM9 covers SDM845 and SDM710 boards, and XM11 covers the SM6125 and SDM710 CPUs in the Redmi Note 8 and Note 8 Pro. Read the CPU marking on your board before you order, because the wrong XM number wastes a stencil and a repair attempt. If your workshop works through several Xiaomi generations, a reballing kit plus the matching XM numbers gives you coverage without forcing one stencil onto a chip it was not cut for. The XM8 suits shops that still see Mi 5 series boards and want a repeatable CPU reballing step in their workflow.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Chip-specific stencil cut for the Qualcomm MSM8996 CPU
- ✓Ultra-thin 0.12 mm stainless steel sheet
- ✓Round and square apertures for rounded, complete solder balls
- ✓High-temperature resistance for repeated reflow cycles
- ✓Resists deformation and metal fatigue
- ✓Built to Relife’s original factory drawings for the target chip
- ✓Covers Xiaomi Mi 5, Mi 5S, Mi 5S Plus, Mi Note 2 and Mi MIX
- ✓Part of the numbered RL-044 Xiaomi stencil range
Specifications
| Brand | Relife |
|---|---|
| Model | RL-044 XM8 |
| Category | BGA Reballing Stencil |
| Compatibility | Xiaomi Mi 5 / Mi 5S / Mi 5S Plus / Mi Note 2 / Mi MIX (Qualcomm MSM8996 CPU) |
| Supported Devices | Xiaomi Mi 5, Mi 5S, Mi 5S Plus, Mi Note 2, Mi MIX |
| Technology | Tin planting stencil with round and square apertures |
| Material | Stainless steel, 0.12 mm thickness |
Common Repair Uses
- ✓CPU reballing and tin planting on MSM8996 Xiaomi boards
- ✓Reballing the MSM8996 CPU after removal with a hot air station
- ✓Replacing a CPU during board-level repair of a dead phone
- ✓Restoring a ball array on a chip that shows lifted or damaged joints
- ✓Tin planting a cleaned CPU before it goes back on the board
- ✓Reflow rework on Mi 5 series boards with a hardware fault
Compatible Devices
- ✓Xiaomi models built on the Qualcomm MSM8996 CPU
- ✓Xiaomi Mi 5
- ✓Xiaomi Mi 5S
- ✓Xiaomi Mi 5S Plus
- ✓Xiaomi Mi Note 2
- ✓Xiaomi Mi MIX
- ✓Qualcomm MSM8996 CPU


