2UUL ST86 Thick Pad Extra Thick Heat Resistant Mat
₨ 4,000
Heat Resistant Silicone Pad for Rework
The 2UUL ST86 Thick Pad Extra Thick Heat mat gives your repair bench a 500 x 300 mm silicone work surface for hot air and soldering sessions. The thickened, anti-static, non-slip body protects the bench from rework heat and holds boards steady while you remove ICs, reflow connectors or stage BGA parts. The easy-clean surface wipes off flux residue after each job. You get one pad that suits a single technician’s bench or a full service center layout. Mechanicpk supplies the ST86 across Pakistan for repair shops that need a dependable BGA welding base.
In stock
2UUL ST86 Heat Resistant Silicone Pad for BGA and Board Rework
The 2UUL ST86 Thick Pad Extra Thick Heat mat turns a bare workbench into a protected rework surface. The 2UUL ST86 heat resistant silicone pad measures 500 x 300 mm, so you get room for a phone, a donor board, tweezers and a flux bottle without crowding the edges. 2UUL builds it from silicone with a thickened body, an anti-static surface and a non-slip base. If you run a hot air station for BGA work, IC change karna jobs or screen separation, you need a surface that tolerates repeated heat without warping. This pad targets exactly that job and keeps your bench top safe underneath.
Thick Silicone Build and Surface Behavior
Thickness separates this pad from the thin rubber sheets that curl after a few weeks near a hot air nozzle. The ST86 comes thickened, enlarged and lengthened compared with ordinary repair mats, and the listing describes the silicone as holding its shape under high temperature. Heat from your station lands on the pad instead of the laminate or wood below. The anti-static surface lowers the risk of static discharge near bare boards, which matters when you handle CPU, PMIC and eMMC boards. The non-slip finish stops the mat from creeping when you push a board or lift a shield. Flux residue wipes away because the surface cleans easily, so the pad stays usable through daily workshop abuse.
Repair Workflow Fit on Your Bench
Place the ST86 under your hot air station and microscope zone and treat it as the base layer of the whole rework setup. During hardware fault diagnosis, you lay the board on the pad, probe it with a multimeter and heat a suspect component without moving the board to a second surface. On dead phone and charging issue jobs, the pad holds the board steady while you lift a charging IC or reflow a connector. A PCB holder or fixture grips better when the silicone sits underneath, because the fixture stops sliding. For BGA reballing, the pad gives you a flat, heat-tolerant area to stage the stencil, the reballing kit and the cleaned chip. ISP and UFS work benefits too. Your ISP pinout tools, eMMC programmers and UFS adapters sit on the same mat beside the board, so wires and adapters never touch a bare metal bench.
Size, Coverage and Bench Planning
At 500 x 300 mm, the pad covers the working zone of a standard repair bench. You can split the area into zones: hot work on one side, cold parts and test boxes on the other. If you run a soldering station and a hot air gun together, keep the iron stand near the pad edge so a stray solder drip lands on silicone instead of your desk. Shop owners who buy for several benches get one consistent size across every station, which simplifies a service center layout and speeds up technician training. A single pad per technician keeps hot work, flux and loose components in one defined area.
Who Should Buy the ST86
Choose this pad if you do daily board-level repair, run a hot air rework station or teach students at a technical institute. It suits a repair shop that wants one durable mat per technician and a service center that needs a safe base for BGA welding. If your current mat shows burn marks or slides under the board, the ST86 replaces it. The package contains one silicone pad, so order one per bench. Complete the desk with a hot air station, soldering station, microscope, multimeter, reballing kit and PCB holder from Mechanicpk, and upgrade your equipment as your workload grows.
| Weight | 1.3 kg |
|---|
Key Features
- ✓Extra thick silicone body that shields the bench from rework heat
- ✓Large 500 x 300 mm working surface
- ✓Heat resistant surface that holds its shape under high temperature
- ✓Anti-static surface for work around bare boards and ICs
- ✓Non-slip finish that keeps the mat and the board steady
- ✓Easy-clean surface that wipes off flux residue
- ✓Suited to BGA welding and hot air rework
- ✓Single-pad package for a one-per-bench setup
Specifications
| Brand Entity | 2UUL |
|---|---|
| Product Entity | 2UUL ST86 Thick Pad, extra thick heat resistant silicone repair mat |
| Technology Entity | Anti-static heat resistant silicone, BGA rework surface |
| Compatible Device Entities | Smartphone motherboards, logic boards, PCB assemblies (universal) |
| Repair Process Entity | Hot air rework, BGA reballing, IC removal, soldering and desoldering |
| Industry Entity | Mobile phone repair and PCB repair workshops in Pakistan |
Common Repair Uses
- ✓BGA welding and reballing support
- ✓IC change karna with a hot air station
- ✓Screen separation and display problem jobs
- ✓Charging port and charging IC repair
- ✓Hardware fault diagnosis with a multimeter
- ✓Dead phone and dead after flash board work
- ✓ISP and eMMC wiring on a protected surface
- ✓Staging parts, stencils and fixtures during rework
Compatible Devices
- ✓Universal bench pad. It works with any smartphone board or PCB you place on it, not tied to a specific model or chipset.
- ✓Samsung motherboards
- ✓Oppo and Vivo motherboards
- ✓Infinix and Tecno motherboards
- ✓iPhone logic boards
- ✓Qualcomm and MediaTek based boards
- ✓eMMC and UFS boards during ISP work
- ✓Donor boards and spare PCB assemblies
- ✓Any board that needs a heat-safe, anti-static surface
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What size is the 2UUL ST86 repair pad?
Is the 2UUL ST86 safe to use under a hot air station for BGA rework?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



