BGA315 NAND Module for JC V1S Pro Programmer

₨ 1

iPhone and iPad NAND Read Write Module

The BGA315 module is a NAND socket built for the JC V1S Pro programmer. It handles read, write and format operations on the NAND chips used in iPhone SE 3, the iPhone 14 series, iPad 10, iPad Air 5 and iPad Pro 6. The module works as a holder, so the V1S Pro host supplies power and control. Once the NAND is desoldered, reballed and cleaned, it seats into the module and the host takes over the data work. Technicians handling a dead phone after a failed flash or corrupted NAND get a direct, purpose-built route to recovery on these models.

Out of stock

13 People watching this product now!
Description

BGA315 NAND Module for JC V1S Pro: Scope, Workflow and Fit

The BGA315 NAND module for JC V1S Pro extends the programmer to the BGA315 NAND family covered by this module. Its role is narrow and specific. It provides the socket interface that lets the V1S Pro read, write and format the chip’s contents. The module cannot operate alone. It sits between the chip on your bench and the programmer’s data logic, so the host must be connected for any operation. If you already run a V1S Pro, this module turns it into a working NAND station for the 14 series generation and the matching iPad models.

Supported Chips and Device Scope

The module targets BGA315 NAND packages found in iPhone SE 3, iPhone 14, iPhone 14 Plus, iPhone 14 Pro, iPhone 14 Pro Max, iPad 10, iPad Air 5 and iPad Pro 6. Check the chip marking and package footprint on the board before you start. The module only fits packages that match the BGA315 layout. Older iPhone generations use different NAND packages, such as BGA110 and BGA70, and those require their own modules on the same host. Confirm the chip type first, because a mismatched module wastes time and can cost you a good board at the test stage.

Repair Workflow on the Bench

The process starts with desoldering the NAND from the logic board using hot air and a controlled temperature profile. Reball the chip with the correct stencil and fresh balls, then clean the flux and residue from the pads. Seat the reballed NAND into the BGA315 module and connect the module to the V1S Pro host. Run the read or write sequence from the software. Take a full dump before any write, since that dump gives you a reference copy if the operation goes wrong. Clean seating and even ball height decide whether the read stays stable, so inspect the package under a microscope before you power the host. A reballing kit and a PCB holder on the same bench make this process far more repeatable.

Where It Fits in Your Service Process

Use this module for board-level NAND recovery when a device hangs on logo, shows a boot loop issue, or fails after a flash attempt and the stored data needs to be read or restored. It also suits dump-first work, where you need an untouched copy of the NAND before attempting any repair. Shops building a complete NAND setup can pair the V1S Pro with a hot air station, a soldering station and a microscope. For IC-level diagnosis, a multimeter and a test box help you confirm the NAND rail before you lift the chip. Match the module to the chip your workflow handles most often, and build the rest of the bench around that choice.

Additional information
Weight0.15 kg
Q & A
Please login to post questions

Key Features

  • Dedicated BGA315 NAND socket for iPhone SE 3 and iPhone 14 series
  • Covers iPad 10, iPad Air 5 and iPad Pro 6 NAND packages
  • Read, write and format NAND data through the V1S Pro host
  • Requires desoldered, reballed and cleaned NAND before seating
  • Runs only with the JC V1S Pro programmer
  • Ships as a module; the V1S Pro host is sold separately
  • Supports a dump-first workflow for safer recovery
  • Package includes 1 BGA315 NAND module

Specifications

BrandJC
ModelBGA315
CategoryNAND Programming Module
CompatibilityJC V1S Pro Programmer
Supported DevicesiPhone SE 3, iPhone 14, iPhone 14 Plus, iPhone 14 Pro, iPhone 14 Pro Max, iPad 10, iPad Air 5, iPad Pro 6
TechnologyNAND read, write and format (BGA315 package)

Common Repair Uses

  • NAND dump, write and format workflows on the listed models
  • NAND data dump before any repair
  • NAND write and format on supported iPhone and iPad boards
  • Recovery of a dead phone after a failed flash
  • Boot loop issue cases linked to corrupted NAND content
  • Logo hang cases where NAND content needs restoring
  • Board-level NAND replacement with desoldering and reballing
  • Reseating and verifying reballed NAND packages for stable reads
  • Pre-repair backup of device NAND data

Compatible Devices

  • Device-specific, limited to the listed iPhone and iPad models
  • iPhone SE 3
  • iPhone 14
  • iPhone 14 Plus
  • iPhone 14 Pro
  • iPhone 14 Pro Max
  • iPad 10
  • iPad Air 5
  • iPad Pro 6

FAQ

What is the product name?
The product name is BGA315 NAND Module for JC V1S Pro Programmer.
What is the brand of this product?
The brand of this product is JC.
What is the model of this product?
The model of this product is BGA315.
What is this product used for?
This product reads, writes and formats NAND chip data on supported iPhone and iPad models when used with the JC V1S Pro programmer.
Which devices are compatible with this product?
This product is compatible with iPhone SE 3, iPhone 14, iPhone 14 Plus, iPhone 14 Pro, iPhone 14 Pro Max, iPad 10, iPad Air 5 and iPad Pro 6.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does this module work without the V1S Pro programmer?
No. The module works only as part of the JC V1S Pro setup and does not operate on its own.
Does the NAND need to be removed from the board?
Yes. The NAND must be desoldered, reballed, cleaned and seated into the module before reading or writing.