Relife RL-727 3D Extreme Edition Screwdriver Cross 1.5
₨ 2,000
Relife RL-727 3D Screwdriver for Precise Phone Screw Removal
The Relife RL-727 3D Extreme Edition screwdriver gives your repair bench a precision cross 1.5 outer head made from imported S2 steel. The 3D tip seats closely in the screw recess, which reduces slipping and stripped heads during back cover and board removal. A built-in magnetizing block keeps the tip permanently magnetized, so screws stay put while you lift a bracket or reach a tight corner. A precision silent bearing in the handle lets the bit turn smoothly under load. The aluminum alloy body and anti-slip finish keep control steady through long sessions, making it a dependable everyday driver for technicians who open phones and electronics all day.
Out of stock
Relife RL-727 3D Screwdriver for Mobile Repair Workflows
The Relife RL-727 3D screwdriver belongs to the disassembly stage of the repair workflow, before any board-level work begins. Its outer head is a cross 1.5 profile, the size you reach for when opening phone back covers, mounting brackets and shield screws. A controlled opening protects the frame, the flex cables and the screw threads, and this tool is built around that goal. Your workflow starts with a fully seated bit. The 3D geometry increases contact area with the screw recess, so force travels down the shaft instead of camming the bit out. You get fewer stripped heads and fewer damaged housings on devices that already need careful handling. For a dead phone or a board headed to the bench for IC work, a clean first opening saves time later.
Precision 3D Outer Head and Bit Geometry
The outer head uses a 3D profile that matches the screw recess more closely than a standard flat-sided tip. This fit matters most on small cross screws, where a loose bit rounds the recess after only a few turns. The head is manufactured from imported S2 steel, a tool steel chosen for toughness at small dimensions. Your bits hold their edge across repeated opening and closing cycles, which keeps the cost per repair low. Check the tip before each job. A worn or rounded recess means the bit is seating on the edges, and you should replace or refine the head before continuing. Keeping the tip sharp protects both the screw and the device housing.
Built-In Magnetizing Block and Silent Bearing Handle
The RL-727 includes a built-in magnetizing block that magnetizes the tip automatically and permanently. Screws stay on the bit during removal, so they do not fall into the internal components of the device. This matters when you work in a cramped chassis where a lost screw can short a board or get trapped under a shield. The handle contains a precision silent bearing at the nut. It lets the shaft turn smoothly while you apply downward pressure, so you feel the screw release instead of fighting friction. Smooth rotation also reduces the chance of cracking plastic posts or lifting a screw out of its boss.
Ergonomic Aluminum Body and Anti-Slip Grip
The handle is machined from high-hardness aluminum alloy. This keeps the tool light enough for long sessions while giving the body enough rigidity to transmit torque cleanly. The anti-slip finish holds your grip when your hands are warm or slightly oily, which happens often during repair work. A large recognition icon on the body helps you identify the bit size at a glance, without picking up a loupe. Hold the tool near the top of the handle for fine control on delicate screws. Use the full palm grip when you need to apply more force to a stuck screw, and keep your wrist straight to avoid fatigue.
Where It Fits on Your Bench
Use this screwdriver alongside your other opening tools. The Y 0.6 and pentalobe 0.8 bits included with the set cover triangle and pentalobe screws that appear in many phone designs. Keep a dedicated bit for each screw type on your bench, so you never switch heads mid-job and risk a worn recess. Pair the RL-727 with your microscope and PCB holder when you move from disassembly into component-level work. Your screwdriver set should sit within reach of your soldering station, so the opening, inspection and repair steps stay in one efficient sequence.
| Weight | 0.3 kg |
|---|
Key Features
- ✓3D outer cross 1.5 head for a secure, slip-resistant fit in screw recesses
- ✓Imported S2 steel head built for repeated opening and closing cycles
- ✓Built-in magnetizing block for automatic, permanent tip magnetization
- ✓Precision silent bearing for smooth rotation under downward pressure
- ✓Aluminum alloy body for a light, rigid handle
- ✓Anti-slip finish for stable grip during long sessions
- ✓Large recognition icon for quick bit identification
- ✓Set includes Y 0.6 and pentalobe 0.8 bits for common phone screw types
Specifications
| Brand | Relife |
|---|---|
| Model | RL-727 |
| Category | Screwdriver |
| Technology | 3D outer head, built-in magnetizing block, precision silent bearing |
| Material | Imported S2 steel head, aluminum alloy body |
Common Repair Uses
- ✓Disassembly and opening of phone and electronics housings, removing internal brackets, and managing screws during controlled reassembly.
- ✓Opening phone back covers and rear housings
- ✓Removing internal brackets and shield screws
- ✓Accessing the board for diagnostics before IC or component work
- ✓Holding screws on the magnetized tip during removal in tight spaces
- ✓Opening electronics enclosures without rounding screw recesses
- ✓Reassembling housings with controlled screw seating
- ✓Preparing a dead phone for board-level repair
- ✓Maintaining telecommunications and electronic equipment during service visits
Compatible Devices
- ✓Universal, not device-specific. Scope covers cross 1.5 screw heads used in phone and electronics disassembly.
- ✓Cross 1.5 screws in mobile phone back covers and frames
- ✓Cross 1.5 screws securing internal brackets and shields
- ✓Cross 1.5 screws in telecommunications equipment housings
- ✓Cross 1.5 screws in general electronic device assemblies
- ✓Cross 1.5 screws in small enclosures with tight access
- ✓Cross 1.5 screws on removable panels and access covers
- ✓Cross 1.5 screws in compact consumer electronics
- ✓Universal fit, verified for cross 1.5 head profile only
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the RL-727 magnetize screws?
Which bit sizes come with the RL-727 set?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



