PM6150L 103 Power IC for Mobile Repair

₨ 350

PM6150L 103 Qualcomm Power IC for Component-Level Repair

The PM6150L power IC is Qualcomm’s companion PMIC in the PM6150 family. It sits beside the main PM6150 on Snapdragon boards and supports the GPIO, flash LED, LED driver, and display backlight functions. You use it when a dead phone or a display and backlight fault traces back to the power section and the board needs an IC change. Mechanicpk supplies the PM6150L 103 for technicians and repair shops across Pakistan who work with hot air rework and verify against the board schematic before replacing.

Out of stock

20 People watching this product now!
Description

PM6150L Power IC: Qualcomm Companion PMIC for Lighting and Display Rails

The PM6150L power IC is a Qualcomm power management IC that pairs with the PM6150 main PMIC. Qualcomm platforms such as SC7180-based designs use this PMIC pair. The PM6150 carries the core power duties, and the PM6150L takes the auxiliary functions around display lighting, flash, and general-purpose signals. Mechanicpk stocks the PM6150L 103 for technicians who diagnose at PCB level and replace the IC instead of scrapping the whole motherboard.

What the PM6150L Handles on the Board

Qualcomm’s PMIC description for this part lists a defined set of peripheral blocks. These include GPIO lines, a flash LED driver, a light pulse generator for indicator and LED control, a WLED driver for display backlight, and a temperature alarm. All of these communicate with the processor over the SPMI bus. That bus link matters on your bench, because a PMIC that stops answering on SPMI can leave a board dead or stuck early in boot.

The backlight function is the most relevant one for daily repair. When a screen shows an image under torchlight but the backlight stays off, the WLED path is a logical place to start your measurements. Flash LED faults give you a second reason to check this IC.

Where It Fits in Your Repair Workflow

You normally reach this IC after the basics are clear. Confirm the display assembly, the flex connector, and the battery first. Then measure the backlight rails and boost signals around the PMIC with a multimeter under a microscope, and compare the readings with the board schematic. If the readings point to the PM6150L and the pads show no damage, an IC replacement is the next step.

This part fits technicians who handle hardware fault repair, not software marna. Flashing cannot fix a failed power IC. If a phone stays dead after flash, you gain more by checking the PMIC than by repeating the flash. For preparation, pair this IC with a hot air station, a quality flux, and a reballing kit if your workflow calls for fresh solder. If your current hot air station cannot hold stable temperature, a better station is the upgrade that improves every IC change you do.

Replacing the IC: Rework Notes

Check the board marking and the pad layout before you order, because PMIC variants differ by platform. Lift the old IC with controlled preheat and hot air, clean the pads fully, and inspect them for lifted tracks. Apply flux, align the new IC under magnification, and bring the board up to temperature evenly. Excess heat risks neighbouring components and the PCB itself, so keep your airflow moderate and your timing disciplined.

After the IC change, test the board in stages. Check for a normal current draw on a bench power supply, confirm the backlight output, and then run the phone through a full boot. A staged test shows you quickly whether the fault was the PMIC or something further along the line.

Why Technicians Source It from Mechanicpk

You need the right IC and a clean supply when you handle rework jobs for customers. Mechanicpk lists the PM6150L 103 with its model suffix so you can match it to your board before you order. The part joins the wider range of mobile phone ICs, hot air stations, microscopes, and reballing kits at Mechanicpk, so you can build your whole repair setup in one place.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Qualcomm PM6150L companion PMIC for the PM6150 family
  • SPMI bus communication with the main processor
  • WLED driver block for display backlight control
  • Flash LED driver block
  • Light pulse generator block for LED and indicator control
  • GPIO lines for general-purpose signals
  • Built-in temperature alarm block
  • Supplied with model suffix 103 for accurate matching

Specifications

BrandQualcomm
ModelPM6150L 103
CategoryMobile Phone Power IC (PMIC)
TechnologySPMI power management IC with GPIO, flash LED, LED driver, and WLED backlight blocks
CompatibilityQualcomm platforms that use the PM6150 / PM6150L PMIC pair, including SC7180-based designs

Common Repair Uses

  • Replacing the IC on a dead phone when power section checks point to the PMIC
  • Fixing a display problem where the image shows but the backlight stays off
  • Repairing flash LED faults traced to the lighting driver block
  • Restoring boards that hang on logo because the PMIC fails early in boot
  • Swapping a heat-damaged PMIC after a short circuit or liquid damage
  • Repairing boards with abnormal current draw linked to the power section
  • Replacing the IC when a board stays dead after flash and the software is ruled out
  • Component-level PCB repair in repair shops and training labs

Compatible Devices

  • Verified scope is the Qualcomm PM6150 / PM6150L platform family. Device-level model compatibility is not verified, so confirm the IC marking on your board before ordering.
  • Qualcomm SC7180-based boards that use the PM6150 / PM6150L PMIC pair
  • Boards that carry a PM6150L marking next to a PM6150 main PMIC
  • Qualcomm Snapdragon motherboards that follow the PM6150 family power design
  • Any board where your schematic names PM6150L as the companion PMIC

FAQ

What is the product name?
The product name is PM6150L 103 Power IC.
What is the brand of this product?
The brand of this product is Qualcomm.
What is the model of this product?
The model of this product is PM6150L 103.
What is this product used for?
This product is used for component-level power IC replacement on boards that use the PM6150L companion PMIC.
Which devices are compatible with this product?
This product is compatible with Qualcomm platforms that use the PM6150 and PM6150L PMIC pair, including SC7180-based designs. Confirm the marking on your board before ordering.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which Qualcomm platform uses the PM6150L?
The PM6150L works as the companion PMIC to the PM6150 on Qualcomm SC7180-based platforms, and your board schematic confirms the exact pairing on your device.
Does the PM6150L control the display backlight?
The PM6150L includes a WLED driver block for display backlight control, so check this IC when the screen shows an image but the backlight stays off, and confirm the circuit against your schematic.