PMR735A 005 Power IC Qualcomm PMIC for Mobile Repair
₨ 450
H2: PMR735A 005 Power IC for SM8350-Class Mobile Repair
The PMR735A 005 power IC is a Qualcomm companion PMIC that supplies regulated rails on Snapdragon boards built on the SM8350, SC7280, and SM6375 platforms. It communicates over the SPMI bus, provides three switching regulators and seven LDOs, and comes in a 48-pin WLNSP package. You use it for PMIC replacement on dead phone cases, abnormal current draw, and rail faults after liquid damage or a short. Match the full PMR735A-005 marking before you order, then confirm the repair with a bench supply and a microscope inspection.
H2: PMR735A 005 Power IC: Qualcomm PMIC for Mobile Repair Benches
The PMR735A 005 power IC is a Qualcomm power management chip that serves Snapdragon boards built on the SM8350, SC7280, and SM6375 platforms. It connects to the SoC through the SPMI bus and delivers regulated rails from three switching regulators and seven LDOs. Teardown records place the PMR735A-005 inside the Oppo Find X5 (PFFM10), where it works next to the PM8350, PM8350B, and PM8350C companion PMICs. When a phone arrives dead or draws abnormal current on the bench supply, this IC belongs on your suspect list. Mechanicpk supplies it for technicians who replace the exact part instead of guessing with a look-alike.
H3: Role of the PMR735A on the Power Tree
The chip acts as a companion PMIC, so it shares the power tree with the other Qualcomm PMICs on the board. Kernel device-tree files describe its regulator set as smps1 to smps3 and ldo1 to ldo7, and they list four GPIO lines plus a die temperature alarm. Those rails supply board sections that the SoC needs during start-up. A fault in this IC can leave the phone with a hang on logo, a boot loop issue, or no power response at all. You separate this from a CPU or storage fault by measuring the rails and the current draw first. Only after those readings do you decide whether the PMIC group needs rework, which saves you from pulling expensive parts without proof.
H3: PMR735A 005 Power IC in the Repair Workflow
Start with a current-limited DC supply and watch the amperage as the board powers up. A stuck or high reading points you toward the PMIC cluster, and a multimeter in diode mode on the rails confirms a short. Inspect the area around the IC under a microscope for liquid residue, burnt pads, and cracked capacitors before you touch the chip. If the diagnosis lands on this part, IC change karna becomes your next step, and a preheater or hot air station gives you controlled heat across the board. After the swap, you test charging, boot, and network function in sequence. A solid PCB holder keeps the board stable during rework, and a stronger rework station is your upgrade path once your repair volume grows.
H3: Replacement and Rework Notes
The package is a 48-pin WLNSP, a small wafer-level footprint with little room for error. Clean the pads flat, apply flux, and align the part under magnification before you apply heat. Keep airflow low and shield neighbouring ICs with heat-resistant tape, because the Qualcomm PMICs sit close together on these boards. Match the full marking, including the suffix, against the original chip. The PMR735B appears on the same platform family, so a similar-looking part can fail to match your board. Reballing gear and a clean solder profile protect the pads on both the donor and the target board. Power the board through a bench supply before you close the phone, so a second fault shows up while the housing is still open.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Qualcomm power management IC with the PMR735A-005 marking
- ✓SPMI bus connection to the SoC
- ✓Three switching regulators (smps1 to smps3)
- ✓Seven LDO regulators (ldo1 to ldo7)
- ✓Four GPIO lines (gpio1 to gpio4)
- ✓Built-in die temperature alarm
- ✓Compact 48-pin WLNSP package
- ✓Used on SM8350, SC7280, and SM6375 platform boards
Specifications
| Brand | Qualcomm |
|---|---|
| Model | PMR735A-005 |
| Category | Power Management IC (PMIC) |
| Compatibility | Qualcomm SM8350, SC7280, and SM6375 platform boards |
| Technology | SPMI interface, 3 SMPS regulators, 7 LDO regulators, 4 GPIOs, die temperature alarm |
| Package | 48-pin WLNSP |
Common Repair Uses
- ✓Real PMIC-level workflows on boards that carry this IC
- ✓Dead phone with no power response
- ✓Abnormal current draw on a bench power supply
- ✓Boot loop issue caused by a failed rail
- ✓Hang on logo after a power fault
- ✓Charging issue after a short or liquid damage
- ✓PMIC replacement after rail tracing finds a shorted output
- ✓Hardware fault diagnosis on Qualcomm power trees
- ✓IC swap from a donor board
Compatible Devices
- ✓Verified scope is the Oppo Find X5 (PFFM10) plus Qualcomm SM8350, SC7280, and SM6375 platform boards that carry the PMR735A
- ✓Oppo Find X5 (PFFM10)
- ✓Qualcomm SM8350 (Snapdragon 888) platform boards
- ✓Qualcomm SC7280 platform boards
- ✓Qualcomm SM6375 (Snapdragon 695) platform boards
- ✓Boards that pair the PMR735A with PM8350, PM8350B, and PM8350C PMICs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I replace a PMR735A with a PMR735B on an SM8350 board?
How do I check for a PMR735A fault with a bench power supply?
Related products
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock



