WTR5975 2VV Network IC – Qualcomm RF Transceiver
₨ 400
WTR5975 2VV Network IC for Gigabit LTE Board Repair
The WTR5975 network IC is a Qualcomm single-chip RF transceiver from the Snapdragon 835 family. It supports Gigabit Class LTE, LTE-U, and LAA with 5 GHz unlicensed band support. It handles up to 4x downlink carrier aggregation, 2x uplink carrier aggregation, and 4×4 MIMO in one package. You replace it at board level when a network fault traces back to the RF transceiver and not to the power amplifier, antenna switch, or baseband. Check the marking on your dead board against this part before you order, and confirm the fault under a microscope before you start IC change.
WTR5975 Network IC for Qualcomm Gigabit LTE Board Repair
The WTR5975 network IC is a Qualcomm single-chip RF transceiver. It sits in the signal path between the antenna front end and the baseband modem. Qualcomm released it in the Snapdragon 835 family as the first single-chip RF IC with Gigabit Class LTE, LTE-U, and LAA support, including 5 GHz unlicensed bands. This WTR5975 2VV listing gives you a replacement transceiver for supported boards when your diagnosis points to the RF IC as the source of a network issue.
How the WTR5975 Works Inside the Radio Chain
The WTR5975 combines transmit and receive paths in one transceiver. It supports up to 4x downlink carrier aggregation, 2x uplink carrier aggregation, all 3GPP-approved bands including the 3.5 GHz bands 42 and 43, and 4×4 MIMO. Older designs needed more than one RF chip for these features, so this part reduces the board footprint for advanced CA and MIMO.
Teardown work by TechInsights found it in the Samsung Galaxy S8, where it works alongside the QET4100 envelope tracking power supply. iFixit lists it in the iPhone X beside the Qualcomm MDM9655 modem. Because the transceiver feeds signals to the modem and takes its control from it, a fault here shows up as a network issue even when the baseband is healthy.
Where It Fits in Your Repair Workflow
Start with diagnosis. Measure the supply rails feeding the RF section, then inspect the transceiver area under a microscope for liquid damage, corrosion, and lifted pads. Rule out the power amplifier, antenna switch, and antenna path before you blame the transceiver. A multimeter check and a visual inspection save you from changing a good IC.
Once you confirm the fault, preheat the board on a PCB holder and use a hot air station with controlled airflow to lift the old IC. Clean the pads, apply flux, and reball or place the new transceiver. After the rework, power the board up and check network registration and signal behavior before you close the phone.
This part belongs with your IC rework kit. Pair it with a hot air station, reballing kit, PCB holder, and microscope from the Mechanicpk catalog. If you do this work daily, a better microscope is the natural upgrade for inspecting fine-pitch RF packages.
Fitment Notes Before You Order
The WTR5975 fits boards designed for it, so compatibility depends on chipset family and not on a universal footprint. Read the marking on the transceiver of your dead board and match it to this part. Do not assume a different Qualcomm transceiver is interchangeable.
Buy this IC when your diagnosis points to the transceiver. A baseband, PMIC, or power amplifier fault produces similar symptoms, and replacing the wrong IC wastes your time and the customer’s money. Verify first, then change the part.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Qualcomm single-chip RF transceiver from the Snapdragon 835 family
- ✓Gigabit Class LTE, LTE-U, and LAA support with 5 GHz unlicensed bands
- ✓Up to 4x downlink carrier aggregation and 2x uplink carrier aggregation
- ✓4x4 MIMO support in one transceiver chip
- ✓Support for all 3GPP-approved bands, including 3.5 GHz bands 42 and 43
- ✓Reduced board footprint compared with multi-chip RF designs
- ✓Verified in the Samsung Galaxy S8 and iPhone X RF sections
- ✓Suited to hot air rework and reballing at board level
Specifications
| Brand | Qualcomm |
|---|---|
| Model | WTR5975 2VV |
| Category | Network IC / RF Transceiver |
| Technology | Single-chip RF transceiver, Gigabit Class LTE, LTE-U, LAA |
| Supported Features | Up to 4x downlink CA, 2x uplink CA, 4x4 MIMO, all 3GPP-approved bands including bands 42 and 43 |
Common Repair Uses
- ✓Replacing a failed RF transceiver after you confirm a no-network or no-service fault
- ✓Fixing a network issue after liquid damage when the transceiver area shows corrosion
- ✓Restoring weak or unstable LTE signal traced to the transceiver on the RF path
- ✓Reworking a transceiver with a lifted pad or damaged solder ball
- ✓Reballing and re-seating a transceiver that shows poor solder contact
- ✓Hardware fault repair on supported Snapdragon 835 boards
Compatible Devices
- ✓Verified scope: boards built around the Qualcomm WTR5975 transceiver. This part is not universal.
- ✓Qualcomm Snapdragon 835 (MSM8998) family boards that use the WTR5975
- ✓Samsung Galaxy S8 boards that use the WTR5975
- ✓Samsung Galaxy S8+ boards that use the WTR5975
- ✓Apple iPhone X boards with the Qualcomm MDM9655 modem
- ✓Mobile LTE dongle designs that use the WTR5975
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the WTR5975 support carrier aggregation and 4x4 MIMO?
Which Snapdragon platform uses the WTR5975 transceiver?
Related products
A3B U2 610A3B Charging Power IC iPhone 7,7+ Tristar U4001
In stock



