PM7150L 103 Power IC for Mobile Repair
₨ 1,200
H2: PM7150L 103 Power IC for Qualcomm-Based Mobile Repair
The PM7150L 103 power IC is a Qualcomm power management IC that you use to replace a failed PMIC on boards built around the PM7150 family. It regulates the supply rails that feed the processor, memory, and peripherals, so a failed unit often shows up as a dead phone, a charging issue, or a device that draws abnormal current. Match the “103” marking on the original IC before you order. Mechanicpk supplies this part to Pakistani repair shops and technicians who handle Qualcomm Snapdragon boards. You get a direct replacement for a confirmed power-section fault, not a guess-and-swap component.
H2: PM7150L 103 Power IC for Qualcomm Snapdragon Board Repair
The PM7150L 103 power IC is a Qualcomm PMIC that sits at the centre of the power tree on supported Snapdragon boards. It converts the battery voltage into the regulated rails that the SoC, RAM, storage, and supporting circuits need to start and run. When this IC fails, the board cannot bring those rails up in sequence, and the phone stays dead or stalls early in boot. The “103” in the part name is the marking you compare against the original IC on the board. Technicians who work on mid-range Qualcomm devices treat the PM7150L as a common replacement part after a short, a liquid event, or a failed rework.
H3: Where the PM7150L Fits in Your Repair Workflow
Start at the diagnostic stage, before you touch the hot air station. Measure current draw on a bench power supply, then read the supply rails with a multimeter. A dead phone that pulls no current, or one that pulls a fixed high current, points you toward the power section. Once you isolate the PMIC, you remove the old IC, clean the pads, and fit the PM7150L 103 using proper BGA rework technique. Test the board with a power supply before you reassemble, then confirm charging and boot.
H3: Identifying the Right Marking Before You Order
Compatibility on PMICs depends on the exact IC marking, not just the phone model. Read the code printed on the original PM7150L and confirm that it ends in 103 before you replace anything. Check your board schematic or boardview file against the part number as well, because Qualcomm platforms share several PM7150-family chips with different roles. A repair listing for the Xiaomi Poco X3 names this part, but you should still verify against the board in front of you. This one check saves you from lifting pads for the wrong IC.
H3: Faults This Power IC Commonly Addresses
You reach for the PM7150L 103 when diagnostics confirm a PMIC-level fault. Typical symptoms include a dead phone, a board that draws no current, a device that heats quickly on a bench supply, and a charging issue where the battery will not take current. A device that shows dead after flash with a good battery and clean software history can also trace back to the power section. Rule out the battery, charging port, and software first. Then replace the IC only after the measurements point at it.
H3: Rework Practice for a Clean Replacement
Set a controlled preheat and use a hot air station with steady airflow. Protect nearby components with flux and heat shielding, since the PMIC sits close to other small parts. Lift the old IC without dragging the pads, clean the area with wick and flux, and inspect for damaged pads or traces before you place the new part. Reball only if your process requires it. Align the new IC under a microscope, because small placement errors cause shorts you cannot see afterward. Let the board cool before you power it up.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Qualcomm PMIC for PM7150L-based boards
- ✓“103” marking you match against the original IC
- ✓Replaces a failed power IC at component level
- ✓Suits dead phone and charging issue repairs
- ✓Works within a standard BGA rework workflow
- ✓Supports bench-power-supply and multimeter diagnostics
- ✓Supplied by Mechanicpk for Pakistani repair shops
- ✓Suits technicians who read schematics and boardviews
Specifications
| Brand | Qualcomm |
|---|---|
| Model | PM7150L 103 |
| Category | Power IC (PMIC) |
| Technology | Power management IC |
| Compatibility | Qualcomm boards that use the PM7150L PMIC |
Common Repair Uses
- ✓Verified real-world workflows for a PMIC replacement part.
- ✓Replacing a failed PMIC on a dead phone
- ✓Fixing a charging issue caused by a faulty power section
- ✓Repairing a board with abnormal current draw after a short
- ✓Restoring a device that stays dead after a liquid event
- ✓Recovering a board after a failed rework attempt
- ✓Servicing a device that shows dead after flash with confirmed power-section failure
- ✓Supplying repair shops that handle Qualcomm Snapdragon motherboards
Compatible Devices
- ✓Verified scope is Qualcomm Snapdragon boards that use the PM7150L PMIC. Confirm the marking and your board schematic before you replace the IC.
- ✓Qualcomm boards using the PM7150L PMIC
- ✓Boards where the original IC carries the PM7150L 103 marking
- ✓Xiaomi Poco X3 (named in repair listings for this part; verify against your board)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How do I confirm the 103 marking before replacing the PM7150L?
Can a faulty PM7150L cause a dead phone with no current draw?
Related products
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock



