VC7643-26 Power Amplifier IC – VanChip RF PAM
₨ 500
VC7643-26 Power Amplifier IC for RF Transmit-Stage Repair
The VC7643-26 power amplifier IC comes from VanChip’s VC7643 RF power amplifier family, a series TechInsights documented across 42 Chinese handset models. It drives the transmit stage of the phone’s RF front end, so you reach for it when a handset boots and charges normally but shows no service, weak bars, or dropped network under load. Check the marking on your donor board, remove the faulty PA with controlled hot air, and fit the replacement. Mechanicpk supplies it for technicians who repair Chinese-brand smartphones at component level.
VC7643-26 Power Amplifier IC for Mobile RF Front-End Repair
The VC7643-26 power amplifier IC belongs to the VC7643 series from VanChip (Tianjin) Technology, a Chinese RF front-end designer that has built power amplifiers and RF switch ICs for smartphones since 2010. The PA IC amplifies the transmit signal before it reaches the antenna path. When it fails, the phone still runs Android normally, but the network side collapses. You get a targeted replacement part for that exact fault instead of a board swap.
Where the PA IC sits in the repair workflow
The RF transceiver generates the low-level transmit signal. The power amplifier raises it to the level the antenna needs for the cell tower to hear the handset. A dead or shorted PA produces classic network issue symptoms: no service, SIM detected but no registration, weak signal beside a working phone, and calls that drop when the handset transmits. Software cannot fix those faults. A clean flash leaves them untouched, which is how you separate a hardware fault from a software one on your repair bench.
What the VC7643 family tells you
TechInsights analysed two variants of the VC7643 module, the -63 and the -63H. The -63 carries seven die and the -63H carries three, and both share one package and printed wiring board with all die wire bonded. TechInsights found the family in 42 Chinese handset models, which tells you the part circulates widely in the Chinese-brand repair market. The -26 suffix marks its own variant. Match the marking on the donor PA before you order, because suffix differences matter in RF parts.
Diagnose before you replace
Start with a multimeter on the PA supply line and check for a short to ground. A shorted PA often heats up and drains the battery faster. Inspect the PA area under a microscope for liquid residue, lifted pads, and corroded pins, since moisture damage commonly kills RF parts. Rule out the SIM tray, the antenna connector, and the RF switch before you commit to a PA change. Replace the PA only when the evidence points at it.
Rework with hot air
IC change karna on an RF module needs patience. Apply flux, preheat the board, and keep airflow low so you do not blow neighboring RF passives off their pads. Lift the old PA once the solder flows, clean the pads, and check for bridges under the microscope. Seat the new VC7643-26 power amplifier IC squarely and reflow it evenly. Test for shorts before you power the board. If your current hot air station lacks fine airflow control, a better station is the natural upgrade for RF work.
Bench fit and inventory
Technicians who repair Chinese-brand smartphones keep PA ICs in stock because network faults return every week. Pair this part with a Multimeter, a Microscope, and a Hot Air Station from Mechanicpk and you cover the full diagnose-and-rework chain. Test the phone for registration, signal strength, and a stable call before you hand it back.
| Weight | 0.1 kg |
|---|
Key Features
- ✓VanChip RF power amplifier design for cellular handsets
- ✓Part of the VC7643 family documented in 42 Chinese handset models
- ✓Replaces the transmit-stage PA on a faulty RF front end
- ✓Family builds use wire-bonded die on a shared board and package
- ✓Fits hot air rework with flux and controlled airflow
- ✓Restores signal on network-fault phones without a board swap
- ✓Matched by the marking printed on the donor PA
- ✓Supplied by Mechanicpk for Pakistani repair shops and service centers
Specifications
| Brand | VanChip |
|---|---|
| Model | VC7643-26 |
| Category | RF Power Amplifier IC (PAM) |
| Technology | RF power amplification for cellular handsets (VC7643 family) |
| Compatibility | Chinese-brand smartphones that use VC7643-family PA modules |
| Supported Devices | Device-level list for the -26 variant is not published; match the PA marking on the donor board |
Common Repair Uses
- ✓Real-world PA IC replacement scenarios on Chinese-brand smartphones.
- ✓No service after a drop or liquid damage
- ✓Weak signal bars when identical phones show normal reception
- ✓Calls that drop when the handset transmits
- ✓SIM detected but no network registration
- ✓Mobile data failing while Wi-Fi works
- ✓Phones with a shorted PA supply line that heat up near the RF area
- ✓Hardware fault confirmed after a clean flash did not restore the network
- ✓Technician training on RF front-end rework
Compatible Devices
- ✓Verified scope is the VanChip VC7643 family used in Chinese-brand handsets. Model-level compatibility for the -26 variant is not verified, so match by marking.
- ✓Chinese-brand smartphones with a VanChip VC7643-family PA on the RF board
- ✓Handsets whose PA IC carries a VC7643-26 marking
- ✓Smartphones that need a cellular transmit-stage PA replacement
- ✓Not device-specific: confirm the donor PA marking before ordering
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How do I confirm a PA IC fault before replacing the VC7643-26?
Can a software flash fix a faulty VC7643-26 power amplifier IC?
Related products
339S00108 WiFi IC For iPad Air iPad Pro 9.7 Replacement
In stock



