SMB1351-022 Charging IC for Mobile Phone Repair
₨ 800
SMB1351 Charging IC for Charging Fault Repair
The SMB1351 charging IC is a Qualcomm programmable switch-mode charger for single-cell lithium-ion and lithium-polymer batteries. Qualcomm rates its conversion efficiency above 90 percent, with charge current up to 4.6 A and autonomous Quick Charge 3.0 support. You use this -022 variant to replace a failed charger chip on a dead, slow-charging, or overheating board instead of scrapping the motherboard. It also covers USB OTG, adaptive input current limit, and automatic power source detection. Match the marking on your failed chip before you order, because this IC is not a universal drop-in for every phone.
SMB1351 Charging IC: Qualcomm Switch-Mode Charger for Phone Repair
The SMB1351 charging IC is a Qualcomm programmable battery charger for single-cell lithium-ion and lithium-polymer designs. It sits directly in the charging path, so a failed chip can leave a phone with no charge, a crawling charge, or a hot board at the connector. This -022 variant gives your repair bench a direct replacement for the failed part, so you swap one chip instead of writing off the PCB. This page explains how the IC works, where it fits in your PCB repair workflow, and how to confirm a match before you pick up the hot air gun.
How the Switch-Mode Architecture Works
Qualcomm designs the SMB1351 as a switch-mode charger with conversion efficiency above 90 percent. That efficiency removes the heat and low-current limits you see with linear charging solutions. The chip delivers charge current up to 4.6 A, and it handles USB OTG, adaptive input current limit (AICL), and automatic power source detection (APSD). It also supports autonomous Quick Charge 3.0, so it negotiates a higher voltage with a compatible adapter without waiting on the main processor. Its dual-input design lets it manage more than one power source on the board. Qualcomm also lists FlexCharge and TurboCharge behavior, including up to 750 mA from a 500 mA USB port and up to 4.5 A from an AC adapter.
Where It Fits in Your Charging-Path Repair Workflow
Start with diagnostics, not the hot air station. Plug the board into your bench power supply and read the current draw. A dead phone that pulls nothing or pulls too much points you toward the charging path. Use your multimeter in diode mode to check VBUS and the battery line for a short. Then inspect the area under a microscope for liquid residue, lifted pads, or burn marks around the charger IC. If the SMB1351 shorts the line, runs hot, or fails to negotiate fast charging with a known good adapter, IC change karna becomes the correct fix. Rule out the connector, the cable, and the battery first, because a worn port often mimics a charger IC fault.
Replacement Technique on Your Repair Bench
Secure the board in a PCB holder and apply flux around the chip. Use your hot air station with a temperature profile suited to the solder alloy on that board, and lift the old IC once the joints flow. Clean the pads with your soldering station and wick, then inspect each pad for damage. If your replacement needs fresh balls or tinned pads, prepare it with your reballing kit before placement. Align the chip, reflow it evenly, and let the board cool without disturbing it. Test in stages: first the idle current, then the charging current, then fast charging with a Quick Charge adapter, then USB OTG if the phone supports it. This sequence confirms the repair and catches a second fault early.
Confirming the Match Before You Order
The SMB1351 is not a universal charging chip, so check the marking on your failed IC and the board layout before you buy. Compare the printed code, including the -022 suffix, against the part you remove. Do not assume compatibility from the phone brand or model name alone, because board revisions change the charging design. Treat this chip as one part of your wider charging-path kit. Pair it with a multimeter, a microscope, a hot air station, and a soldering station, and you cover the full diagnose, replace, and test cycle. If a repair needs a different charger or power management IC, browse the charging ICs and power management ICs categories on Mechanicpk.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Qualcomm programmable single-cell Li-ion and Li-polymer charger
- ✓Switch-mode operation with conversion efficiency above 90 percent
- ✓Charge current up to 4.6 A
- ✓Autonomous Quick Charge 3.0 support
- ✓Dual-input charging design
- ✓USB OTG support
- ✓Adaptive input current limit and automatic power source detection
- ✓FlexCharge and TurboCharge behavior per Qualcomm
Specifications
| Brand | Qualcomm |
|---|---|
| Model | SMB1351-022 |
| Category | Charging IC / Battery Charger IC |
| Compatibility | Single-cell lithium-ion and lithium-polymer battery designs |
| Technology | Programmable switch-mode charging, Quick Charge 3.0, USB OTG, AICL, APSD |
| Output Current | Up to 4.6 A charge current |
Common Repair Uses
- ✓Charging-path repair on boards that carry the SMB1351.
- ✓Replace a failed charger IC on a dead phone that draws no current
- ✓Fix a charging issue where the phone charges very slowly
- ✓Repair a board that overheats near the charging connector
- ✓Clear a VBUS-to-ground short traced to the charger IC
- ✓Restore Quick Charge detection when the adapter is not recognized as fast charging
- ✓Recover USB OTG function after a charger IC fault
- ✓Repair charging faults after liquid damage once you confirm the IC has failed
- ✓Replace the IC during PCB-level rework when the old chip lifts pads or burns out
Compatible Devices
- ✓Universal, not device-specific. Verified scope is boards that use the SMB1351 as their battery charger; confirm the marking on your failed chip before ordering.
- ✓Boards that use the SMB1351 as the main battery charger
- ✓Single-cell lithium-ion battery designs
- ✓Single-cell lithium-polymer battery designs
- ✓Designs with Quick Charge 3.0 adapter input
- ✓Designs with standard USB charging input
- ✓Designs with AC adapter input using TurboCharge behavior
- ✓Designs that use USB OTG
- ✓Dual-input charging circuits
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the SMB1351 charging IC support Quick Charge 3.0?
What is the maximum charge current of the SMB1351 and does it support USB OTG?
Related products
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock
A3B U2 610A3B Charging Power IC iPhone 7,7+ Tristar U4001
In stock



