PM7250 003 Power IC – Qualcomm PMIC for Redmi K30

₨ 500

PM7250 003 Power IC for Qualcomm Board-Level Repair

The PM7250 003 power IC is a Qualcomm power management IC in a BGA package, built for replacement on Xiaomi Redmi K30 series motherboards. It sequences the supply rails that wake the board, route battery power, and feed the processor and peripherals. When you trace a no-power, no-charge, or random shutdown fault to the PMIC, this chip gives you a direct component-level fix. You need hot air rework, flux, and a steady hand to fit it, and you finish the job without replacing the whole logic board.

14 People watching this product now!
Description

PM7250 003 Power IC: Qualcomm PMIC for Board-Level Power Repair

The PM7250 003 power IC is a Qualcomm PMIC that controls power distribution on Redmi K30 series logic boards. Every voltage rail on the board starts at the power management stage, so a failed PMIC takes the whole phone down with it. You see the result as a dead phone, a board that ignores the charger, or a handset that restarts without warning. This BGA component is the replacement part for that fault. You lift the failed chip with hot air, prepare the pads, and reflow a fresh PM7250 003 into place. Mechanicpk supplies it to technicians and repair shops across Pakistan who handle power faults at component level.

Where the PMIC Sits in Your Power Diagnosis

A PMIC sits between the battery, the charging path, and the processor. It brings up the rails in a fixed order during boot, so the CPU, memory, and peripherals receive their supply at the right moment. When that sequence breaks, the symptoms look different but share one root: no power-on, boot loop issue, hang on logo, or a sudden shutdown under load. Check the basics before you condemn the IC. Measure the battery connector voltage, inspect the charging port, and watch the current draw on a bench power supply. A short on the main power line or an abnormal current reading points toward the PMIC. A phone that draws zero current on a healthy battery usually points to the battery connector, the power key flex, or an open line instead. Use a multimeter and freeze spray or a thermal camera to find a hot component before you replace anything. This diagnostic discipline protects your bench from unnecessary rework and protects the customer’s board from extra heat cycles.

Reballing and Reflow Workflow

Replacing a PMIC is a heat-control job. Apply flux, preheat the board from below, and lift the old chip with your hot air station at a temperature that suits the solder on that board. Clean the pads with braid and fresh flux, then inspect them under a microscope for lifted or damaged pads before you go further. Reball the new IC with a matching stencil, or align it against the silkscreen outline on the board, and reflow it evenly so every ball collapses without bridging. Let the board cool naturally. Test with a bench supply before you reassemble. A stable idle current and a normal power-on tell you the joint is good. Shield neighbouring chips from direct airflow, because memory and the processor sit close to the PMIC on compact boards. Practise on a scrap board first if you have not reflowed this footprint before.

Confirming the PM7250 003 Power IC Before You Order

The PM7250 003 is a specific part number, so read the marking on the chip you remove before you order. A similar-looking code such as PM7250B is a different part number and does not automatically interchange with it. Compare the full marking under the microscope and check your board revision against the Redmi K30 series. Confirm the fault with measurements instead of guesswork, because a good PMIC replaced on a board with a different fault wastes your time and the customer’s money. You also need the right tools on your bench: a hot air station, BGA reballing tools, flux, solder balls, and microscope access. Keep spare stencils close if you reball often, and store the IC in an anti-static pouch until the moment you place it.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Genuine Qualcomm PMIC part number PM7250-003
  • BGA package for board-level soldering
  • Controls power distribution and rail sequencing
  • Targets Xiaomi Redmi K30 series motherboards
  • Fixes no-power and no-charge faults after correct diagnosis
  • Supports reballing with a matching stencil
  • Saves the cost of a full logic board replacement
  • Suits technicians with hot air rework equipment

Specifications

BrandQualcomm
ModelPM7250-003
CategoryPower IC (Power Management IC)
CompatibilityXiaomi Redmi K30 series motherboards
TechnologyPMIC, BGA package

Common Repair Uses

  • Real-world board-level repair scenarios for a PMIC replacement.
  • Dead phone with no power-on after the battery and connector test clean
  • Phone that ignores the charger when the port and cable test good
  • Boot loop issue caused by a failed power rail
  • Hang on logo or random shutdown linked to power faults
  • Short on the main power line traced to the PMIC
  • Board damaged after liquid exposure where the PMIC fails the check
  • IC change karna after a failed previous repair or heat damage
  • Hot air reballing and reflow practice on donor boards

Compatible Devices

  • Verified scope: Xiaomi Redmi K30 series boards that carry the PM7250 003 PMIC. Confirm the marking on your board before you order.
  • Xiaomi Redmi K30 series motherboards
  • Boards that carry the PM7250 003 marking on the original power management IC
  • Qualcomm-platform boards where the failed PMIC reads PM7250 003

FAQ

What is the product name?
The product name is PM7250 003 Power IC.
What is the brand of this product?
The brand of this product is Qualcomm.
What is the model of this product?
The model of this product is PM7250-003.
What is this product used for?
This product is used for replacing a failed power management IC on compatible motherboards.
Which devices are compatible with this product?
This product is compatible with Xiaomi Redmi K30 series boards that use the PM7250 003 PMIC.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can I use a PM7250B instead of the PM7250 003?
Match the full marking printed on the original chip. A PM7250B is a separate part number, so do not treat it as a direct replacement.
Which symptoms point to a faulty PM7250 003 on a Redmi K30?
Dead phone, no charging response, boot loop, and random shutdown can all point to the PMIC. Confirm with bench supply current draw and a short check before you replace it.