PMB6830 Baseband Power IC – BGA PMIC

₨ 450

PMB6830 Baseband Power IC for Board-Level Repair

The PMB6830 is a BGA baseband power IC for technicians who work on board-level power faults. You get a chip with the PMB6830 E102 A2 marking, which you should confirm against your target board before fitting. This part suits reballing and hot air rework benches where you test rails and current draw after replacement. Use it for dead phone and no-power diagnosis once you have ruled out simpler causes. Pair it with a controlled hot air station, a matched stencil, and flux for consistent results.

12 People watching this product now!
Description

PMB6830 Baseband Power IC Replacement for Your Repair Bench

The PMB6830 baseband power IC is a BGA power management chip that you replace at the hot air station. Your workflow starts with reading the marking on the chip, which shows PMB6830 with E102 A2 on the top surface. Treat this part as a board-level replacement, not a quick swap. You test the power rails, rework the BGA footprint, and verify the result under load before the board goes back to the customer. Each stage below follows that order.

Identifying the Chip Before Fitting

Read the top marking first, and compare it with the reference you use for the target board. A matching marking alone does not prove the part belongs on that board, so confirm the fitment with your board records. Keep the removed chip for comparison when you have it, and set aside any unlabeled stock until you know its source. Record the marking, the board, and the fault you fixed in your repair log. This habit prevents a second visit when a similar chip looks identical under the microscope.

Reballing and Hot Air Reflow

Lift the old IC with hot air while you shield neighboring components from the heat. Clean the pads with flux and solder braid, then check for lifted or cracked pads under magnification. Apply fresh balls through a stencil that matches the ball pitch, because uneven balls cause open joints. Align the new chip with flux, then reflow at a steady temperature profile rather than pushing heat quickly. Let the board cool on its own before you handle it, since rushed cooling stresses the joints.

Testing the Repaired Board

Connect the board to a regulated DC supply and set a current limit before you power it. Watch the current draw during boot, because a high reading points to a short on a rail rather than a fault in the chip. Measure the outputs with a multimeter against your reference values for that board. Confirm the device reaches the boot logo and holds a steady state for several minutes. Return the board to the customer only after it passes these checks.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • BGA package suited for hot air rework
  • Top marking reads PMB6830 with E102 A2
  • Fits reballing and IC change workflows
  • Requires a stencil matched to its ball pitch
  • Needs ESD-safe handling on the repair bench
  • Board-level replacement part for power faults

Specifications

ModelPMB6830 (E102 marking)
CategoryBaseband Power IC
TechnologyBGA package
CompatibilityXiaomi Mi Pad 2 (seller listing only, confirm before fitting)

Common Repair Uses

  • Baseband power rail troubleshooting
  • Dead phone and no-power diagnosis after rails are checked
  • IC change on BGA power IC boards
  • Reballing and hot air rework practice
  • Board-level power distribution repair
  • Board testing after reflow

Compatible Devices

  • Verified scope is limited. Device-specific compatibility is not confirmed by manufacturer data.
  • Xiaomi Mi Pad 2 (seller listing only, confirm the board before fitting)
  • Other boards: check the reference designator and board records before fitting

FAQ

What is the product name?
The product name is PMB6830 Baseband Power IC.
What is the model of this product?
The model is PMB6830, marked E102 A2 on the top surface.
What is this product used for?
This product is used for board-level baseband power repair, including IC change and reballing.
Which devices are compatible with this product?
This product is listed as compatible with Xiaomi Mi Pad 2 by a seller. Confirm fitment against your target board before installation.
Who should use this product?
This product suits mobile repair technicians, repair shops, service centers, and professional users.
Does the PMB6830 need reballing before fitting?
Yes. It uses a BGA package, so you reball it on a matched stencil before mounting it on the board.
How do you verify the PMB6830 marking before fitting?
Compare the top marking with your board reference and records, because a matching marking alone does not confirm fitment.