D9 9-Pin Backlight IC for iPhone 6 and 6 Plus
₨ 450
D9 Backlight IC Board-Level Repair
The D9 9-pin backlight IC is a BGA-packaged control chip for the backlight boost stage on iPhone 6 and iPhone 6 Plus logic boards. It sits at the U1503 position and is identified by its D9 marking on the package. It suits jobs where the display shows an image but the backlight stays dark or dim. Replacement requires hot air rework with a 9-pin BGA profile, clean pads, and microscope-checked placement. Confirm the fault on the board before replacing, since passives on the same node can produce the same symptoms.
D9 9-Pin Backlight IC for iPhone 6 and 6 Plus Logic Boards
The D9 9-pin backlight IC is a replacement part for the backlight boost stage on iPhone 6 and iPhone 6 Plus logic boards. It sits at the U1503 position and supplies the boosted voltage that drives the LCD backlight. When this stage fails, the handset usually boots, the touchscreen responds, and the panel stays dark or dim under a flashlight. You get the clearest picture of the fault by checking boost output before you lift anything. That keeps the diagnosis focused on the backlight path instead of the display assembly.
Fault Diagnosis on the Bench
Start by separating a backlight fault from a panel or image fault. Power the board, confirm the touch digitizer responds, and measure the backlight boost output at the U1503 node with a multimeter. A missing or low reading points toward the IC or its immediate passives. Under the microscope, check for lifted pads, cracked balls, and liquid corrosion around the package. Those signs often explain the fault without further testing. Record your readings before you remove the chip so you can compare them after reassembly.
Replacement Workflow
Remove the old IC with a hot air station set to a 9-pin BGA profile, keeping the nozzle centered to avoid heating neighboring parts. Clean the pads with flux and braid, then check them for lifting before placement. Align all nine contacts of the new D9 chip under the microscope before reflow. A single cold joint or shifted ball leaves the backlight circuit open, so inspect each joint once the board cools. Power up the board and verify the boost output before you close the job.
Where This IC Fits in Your Repair Line
This chip belongs in iPhone 6-series backlight and display work, alongside your standard board-level tools. The same hot air station, microscope, and BGA fixture setup used for power and charging IC work applies here. Many backlight faults involve the coil and filter components on the same node, so check those in the same repair pass. Stocking the D9 chip separately from full kits lets you source only what the diagnosis calls for, which keeps repair costs down for you and your customer.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Replacement for the U1503 backlight boost position on iPhone 6 and 6 Plus boards
- ✓BGA package for hot air rework and microscope-aligned placement
- ✓Addresses no-backlight and dim-display symptoms tied to the boost stage
- ✓Marked D9 for quick visual identification on the board
- ✓Suited to standard 9-pin BGA reflow and reballing procedures
- ✓Compact footprint for board-level repair workflows
Specifications
| Model | D9 9-Pin Light IC |
|---|---|
| Category | Mobile Phone ICs |
| Compatibility | iPhone 6, iPhone 6 Plus |
| Technology | BGA backlight boost IC |
| Supported Devices | iPhone 6, iPhone 6 Plus |
| Weight | 0.01 kg |
Common Repair Uses
- ✓No-backlight faults with a working display image
- ✓Dim display faults traced to the boost stage
- ✓Board-level BGA reballing and replacement at U1503
- ✓Hot air rework of the backlight boost node
Compatible Devices
- ✓iPhone 6 logic board (U1503 position)
- ✓iPhone 6 Plus logic board (U1503 position)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does this IC fix a phone with no backlight but a working display image?
Can a cracked joint on U1503 be reflowed instead of replacing the chip?
Related products
339S00108 WiFi IC For iPad Air iPad Pro 9.7 Replacement
In stock
358S IC T211 Samsung Tab Charging IC – Tab 3 USB Charger IC
In stock
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock



