2UUL FD15 Find210-O BallPoint Golden Soldering Iron Tip
₨ 1,200
C210 Ball Point Soldering Tip for Micro-Soldering
The 2UUL FD15 Find210-O BallPoint Golden Soldering Iron Tip is a gold-plated C210 ball point soldering tip built for pinpoint heat transfer on mobile PCBs. The rounded tip delivers stable thermal contact on small pads, vias, mid-layer areas, FPC connectors, and fine SMD components. It fits C210/T210-compatible handles and stations, including the 2UUL FIND210, so it slots into your existing bench setup. Mobile repair technicians in Pakistan reach for this tip during pad repair, connector rework, and board-level hardware fault work. The pack contains one tip.
In stock
C210 Ball Point Soldering Tip Built for Board-Level Precision
The 2UUL FD15 Find210-O BallPoint Golden Soldering Iron Tip gives your C210/T210 bench a dedicated ball-geometry option for micro-soldering. 2UUL lists the model as Find210-O with the code FD15, and it works with the company’s own FIND210 station as well as other C210-compatible holders. As a C210 ball point soldering tip, it targets jobs where you need controlled heat on one pad without disturbing its neighbours. The rounded contact surface keeps thermal contact stable on small pads, which helps solder flow cleanly onto the joint. Mechanicpk supplies it for technicians who solder under a microscope every day and want a repeatable contact point on fine board work. Whether you run a one-bench repair shop or a multi-technician service center, a ball point tip earns its place next to your standard conical and chisel tips.
Gold-Plated Ball Tip Geometry and Heat Transfer
2UUL describes the FD15 as a ball-point tip with a gold-plated finish. The plating supports rapid heat conduction and good solder wettability, which matters when you tin a pad and expect the solder to flow on the first pass. Fine-pitch connector pads punish a tip that drags solder across the board, so a rounded point that tins cleanly saves rework. It also improves corrosion resistance, so the tip holds its surface condition longer between cleanings. The ball shape concentrates heat at a single contact point, giving you pinpoint control on tight pad layouts. Pair the tip with a station that holds temperature accurately. On the 2UUL FIND210, the temperature control range runs from 90°C to 480°C, so you set heat to match the solder alloy and the thermal mass of the board in front of you. Set the temperature before you touch the board, and avoid long dwell times on lifted or damaged pads. Wipe the plated surface and keep the tip tinned after each job to protect the finish.
Where the Tip Fits in Your Mobile Repair Workflow
Board-level mobile repair rewards a tip that reaches one joint at a time. The FD15 suits solder pads, vias, inner-layer and mid-layer areas, connectors, and small SMD components, so you can use it across a long list of hardware fault jobs. Mid-layer work shows the value best: the tip reaches a recessed pad on a phone’s middle layer without crowding the shield cans around it. Typical bench tasks include re-tinning a worn pad after an IC replacement, soldering a fine jumper wire to a via, and reflowing an FPC connector on a phone with a charging issue or a display problem. After you lift a faulty component with a hot air station, you clean the pads, tin them with the ball tip, and place the new part on a prepared surface. On a dead phone that needs ISP access, the ball tip also helps you attach thin wires to test points before you connect your ISP Pinout Tools. Charging issue and network issue repairs often end with a connector or pad reflow, so a precise tip shortens the job. Work under a microscope, hold the board in a PCB holder, and confirm continuity with a multimeter after each repair.
Compatibility and Setup Path for Your Bench
The FD15 fits C210/T210-compatible holders and stations. That covers the 2UUL FIND210 and 2UUL NT210 NextTip stations, plus the JBC T210 handle series, which uses the C210 cartridge range. Confirm that your handle takes C210-series cartridges before you order. The pack contains one tip, so keep a spare on the bench because tips wear with heavy daily use. A single-piece pack suits technicians who replace one worn tip and shops that stock several tip shapes side by side. If you are building out your soldering setup, start with a reliable soldering station, add hot air stations for component removal, and move up to reballing kits and test boxes as your repair range grows. This tip sits at the precision end of that path, where small pads and connector joints decide whether a repair holds.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Ball-point tip geometry for pinpoint heat on small pads
- ✓Gold-plated finish for rapid heat conduction and good wettability
- ✓Corrosion-resistant plated surface
- ✓Fits C210/T210-compatible holders and stations, including 2UUL FIND210
- ✓Works on pads, vias, inner layers, mid-layer areas, and connectors
- ✓Handles FPC connector joints and fine SMD components
- ✓Lightweight 2.5 g net tip
- ✓Single-tip pack in original 2UUL packaging
Specifications
| Brand | 2UUL |
|---|---|
| Model | Find210-O / FD15 |
| Category | Soldering Iron Tips |
| Compatibility | C210 / T210 compatible holders and stations (e.g., 2UUL FIND210) |
| Technology | BallPoint tip, gold-plated, C210/T210 system |
| Weight | 2.5 g (net) |
Common Repair Uses
- ✓Pad, via, connector, and small SMD soldering on mobile PCBs
- ✓Re-tinning worn or cleaned solder pads
- ✓Pad preparation after IC replacement
- ✓Attaching fine jumper wires to vias and test points
- ✓Soldering inner-layer and mid-layer areas
- ✓Reflowing FPC connectors for display and charging issue repairs
- ✓Touch-up on board connector joints
- ✓Soldering small SMD components
- ✓Hardware fault repair on dead phones at board level
Compatible Devices
- ✓Universal C210/T210-system tip, not specific to any phone model
- ✓2UUL FIND210 soldering station
- ✓2UUL NT210 NextTip soldering station
- ✓Stations and holders built for C210 tips
- ✓Soldering stations that use T210 handles
- ✓JBC T210 precision handle series (C210 cartridge range)
- ✓Mobile phone motherboards from any brand (universal tip)
- ✓Phone mid-layer and middle-frame PCB areas
- ✓FPC connector pads and small SMD pad layouts



