338S00739 Audio IC for iPhone 13 Series Repair
₨ 650
iPhone 13 Series Audio Codec Replacement
The 338S00739 is the large audio codec IC in the iPhone 13 series, and it controls the signal path to the loudspeaker, earpiece, and microphone. Technicians replace it when a handset shows no call audio, a dead loudspeaker, or a microphone that callers cannot hear. Confirm the marking on your board before you order, because the smaller audio ICs on the same logic board carry different part numbers. This listing covers the big audio position only, so match it to the board you are working on and test the replacement before the unit goes back to the customer.
338S00739 Audio IC for iPhone 13 Series Repair
The 338S00739 audio IC is the large audio codec on the iPhone 13 series logic board. It converts digital audio from the processor into analog signals for the speaker and earpiece, and it converts microphone input back into digital data. When a handset shows silent calls, a dead loudspeaker, or a microphone fault, this component is a primary suspect on the board. Use this page to identify the correct big audio position, match your board marking, and plan a board-level replacement that restores the full audio path.
Where This IC Sits in the Audio Path
Audio faults on the iPhone 13 can look alike, because the codec and the smaller amplifier ICs share the same signal chain. The big codec handles the core conversion between the processor and the transducers, so a failure here often affects more than one output at once. Before you lift anything, check whether the fault appears on the loudspeaker, the earpiece, the microphone, or all three. A fault that hits both outputs points toward the codec, while a single-output fault usually points toward the amplifier stage. Confirm power rails feeding the codec with your multimeter before you commit to a replacement.
Typical Repair Scenarios on iPhone 13 Boards
The most common complaints are no sound during calls, a microphone callers cannot hear, and audio distortion that appears after liquid exposure or a hard drop. Liquid damage frequently corrodes the codec pads underneath the chip, so inspect the area under a microscope for lifted pads, green residue, or bridged connections. Clean the board fully with flux remover and an ultrasonic or brush cleaning step before you reflow or replace the IC. Skipping this step often leaves a fresh replacement dead within days, because the corrosion keeps working on the new joints.
Replacement and Testing Workflow
Remove the old codec with a hot air station set to a controlled temperature, and protect neighbouring components with kapton tape or a shield. Clean the pads, apply fresh flux, and align the new 338S00739 to the pad layout and the marking on the board before you reflow it. Keep the heat even and short so the board does not warp or lift nearby parts. After installation, test the loudspeaker, earpiece, and microphone in diagnostics, then run a real call test. A clean replacement should restore all three paths without new noise, distortion, or intermittent dropouts.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Large audio codec position for iPhone 13 series boards
- ✓Handles conversion for loudspeaker, earpiece, and microphone paths
- ✓Board-level replacement for technicians with hot air rework skills
- ✓Matches the big audio IC marking used in iPhone 13 repair
- ✓Suitable for no-sound and microphone fault repairs
- ✓Supports full audio path testing after installation
Specifications
| Model | 338S00739 |
|---|---|
| Category | iPhone Audio IC |
| Compatibility | iPhone 13 series |
| Supported Devices | iPhone 13, iPhone 13 mini, iPhone 13 Pro, iPhone 13 Pro Max |
| Technology | Audio codec IC for board-level replacement |
Common Repair Uses
- ✓Board-level audio codec replacement for the iPhone 13 series
- ✓No sound on calls, earpiece fault
- ✓Dead or silent loudspeaker tied to codec failure
- ✓Microphone not heard by callers
- ✓Audio distortion after liquid damage
- ✓Codec pad repair after corrosion or lifted pads
- ✓Replacement after diagnostics confirm the codec is faulty
Compatible Devices
- ✓iPhone 13 series, verified for iPhone 13, iPhone 13 mini, iPhone 13 Pro, and iPhone 13 Pro Max
- ✓iPhone 13
- ✓iPhone 13 mini
- ✓iPhone 13 Pro
- ✓iPhone 13 Pro Max
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which iPhone models use the 338S00739 audio IC?
Does the 338S00739 differ from the small audio IC on iPhone 13?
Related products
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock
U2 Charging iPhone 8, iPhone 8 Plus, iPhone X Chip – 1612A1
In stock



