77912-21 Network IC – Skyworks Tx-Rx Front-End Module
₨ 250
77912-21 Network IC for GSM/EDGE Handset Repair
The 77912-21 network IC is the Skyworks SKY77912-21 Tx-Rx front-end module for quad-band GSM, GPRS, and EDGE handsets. It packs a GaAs HBT power amplifier, ten linear TRx switch ports, an integrated directional coupler, and a MIPI RFFE controller into a 38-pad, 5.5 x 5.3 x 0.8 mm package. It also supports TD-SCDMA bands 34 and 39 and TDD LTE band 39. You replace it at component level when a board shows no service, weak signal, or a failed transmit path, and you skip the cost of a full board swap.
77912-21 Network IC: Skyworks SKY77912-21 Tx-Rx Front-End Module
The 77912-21 network IC is the Skyworks SKY77912-21, a transmit-receive front-end module that links the radio transceiver to the antenna on supported handset boards. One 38-pad package, 5.5 mm x 5.3 mm x 0.8 mm at maximum, holds a GaAs HBT power amplifier, ten linear TRx switch ports, an integrated directional coupler, and a CMOS controller with MIPI RFFE logic. Skyworks designed it for quad-band GSM/GPRS/EDGE handsets with TD-SCDMA and TDD LTE band 39 support, and it adds a notch filter for Wi-Fi coexistence. When a board shows a network issue, weak signal, or a dead GSM transmit path, you can trace the fault to this module and replace it instead of scrapping the board.
Inside the SKY77912-21: Signal Path and Control Logic
Skyworks built this module around quad-band GSM, GPRS, and EDGE transmission. It covers Class 4 operation on GSM850 and GSM900, Class 1 on DCS1800 and PCS1900, Class 12 GPRS multi-slot operation, and linear EDGE. It also handles dual-band TD-SCDMA on bands 34 and 39, plus TDD LTE band 39 transmission. The CMOS controller selects PA band and mode, sets bias, and decodes the switch ports. You get a choice between linear RF control and analog VRAMP control of the GMSK envelope, and each has its own MIPI register mapping. The module supports APT and a buck DC-DC supply, holds Tx harmonics below −40 dBm, and protects the PA against over-voltage and over-current. RF ports match internally to 50 ohms, so you need no extra matching parts around the module. Low-band and high-band input switching lets the phone route 3G and 4G transmit paths through the same front end.
Where the 77912-21 Network IC Fits in Your Repair Workflow
Start with software before you touch the board. Rule out IMEI and baseband corruption, then check the SIM tray, antenna contacts, and any liquid damage or impact marks near the RF section. If the handset still shows no service, a failed network search, or no GSM transmit, move to hardware fault diagnosis under a microscope and inspect the front-end module for lifted pads, cracked corners, or corrosion. Use your multimeter to check the supply feeding the module before you condemn it, since a missing supply produces the same no-network symptom as a failed PA. Once you confirm the fault, IC change karna is straightforward: lift the module with a hot air station and preheater, clean the pads, and fit the replacement. Match the part marking and orientation before you remove the old module, because a 38-pad layout leaves no room for a misaligned placement. Test signal and call behavior on the bench before you close the phone.
Sourcing and Compatibility Notes for Your Bench
Skyworks lists the SKY77912-21 as discontinued and not recommended for new designs, so demand comes from repairing existing handsets. That makes part matching critical. Read the marking on the donor module, confirm it reads 77912-21 and not a sibling such as the 14-port SKY77916-21, and compare the pad footprint before you order. The TD-SCDMA and band 39 support points to handsets built for the China market, so check the board or donor part before you assume a swap. Buy from a supplier that lets you inspect the marking and packaging, and keep the module in anti-static packaging until you place it. Pair it with a microscope, a hot air station, a reballing kit, a PCB holder, and a multimeter from the Mechanicpk repair accessory categories. If you handle denser RF boards, a hot air station with a preheater gives you the cleanest removals and the logical next step up.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Quad-band GSM/GPRS/EDGE front end with Class 12 GPRS multi-slot and linear EDGE
- ✓TD-SCDMA bands 34/39 and TDD LTE band 39 support
- ✓Ten low-loss, high-linearity TRx switch ports
- ✓MIPI RFFE control with user-selectable register mappings
- ✓Linear RF or VRAMP-based GMSK power control
- ✓Integrated broadband directional coupler and Wi-Fi coexistence notch filter
- ✓PA over-voltage and over-current protection, Tx harmonics below −40 dBm
- ✓Compact 38-pad package, 5.5 x 5.3 x 0.8 mm max
Specifications
| Brand | Skyworks |
|---|---|
| Model | SKY77912-21 |
| Category | Tx-Rx Front-End Module (Mobile Phone Network IC) |
| Compatibility | Quad-band GSM/GPRS/EDGE, TD-SCDMA bands 34/39, TDD LTE band 39 handset radios |
| Technology | GaAs HBT power amplifier, CMOS controller, MIPI RFFE control, 50 Ω matched RF ports |
| Dimensions | 5.5 mm x 5.3 mm x 0.8 mm max, 38-pad SMT package |
Common Repair Uses
- ✓Component-level repair of handsets with front-end module faults in the GSM/EDGE transmit and receive path.
- ✓Fixing no network or no service after software and SIM checks
- ✓Restoring GSM transmit on boards with a failed PA path
- ✓Repairing weak signal and low signal bars from a damaged front end
- ✓Replacing modules hit by liquid damage or corrosion in the RF section
- ✓Replacing modules with cracked corners or lifted pads after impact
- ✓Curing transmit-path call drops traced to the module
- ✓IC change karna at component level instead of replacing the board
- ✓Bench-testing donor boards to confirm the 77912-21 part marking
Compatible Devices
- ✓Handsets whose boards carry the Skyworks SKY77912-21 module. Device-level model compatibility is not verified, so confirm the 77912-21 marking on your board before ordering.
- ✓Boards carrying a module marked 77912-21
- ✓Quad-band GSM850/GSM900/DCS1800/PCS1900 handset radios
- ✓GPRS Class 12 multi-slot designs
- ✓Linear EDGE designs
- ✓TD-SCDMA band 34 handsets
- ✓TD-SCDMA band 39 handsets
- ✓TDD LTE band 39 handsets
- ✓Boards using MIPI RFFE control with APT or buck DC-DC supply
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the 77912-21 network IC support 4G LTE?
Can I use a 77912-11 or 77916-21 in place of the 77912-21 network IC?
Related products
339S00108 WiFi IC For iPad Air iPad Pro 9.7 Replacement
In stock
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
U2 Charging iPhone 8, iPhone 8 Plus, iPhone X Chip – 1612A1
In stock



