AW87319 Audio IC Smart K Amplifier for Mobile Repair

₨ 250

H2: AW87319 Audio IC for Smartphone Speaker and Receiver Repair
The AW87319 audio IC from Awinic is a second-generation Smart K amplifier with an integrated 8.5V synchronous boost and Class D output stage. It delivers 4.1W into an 8Ω load and 4.6W into 6Ω, with 47µV speaker noise and 0.015% THD+N. One chip covers both loudspeaker and receiver duty, controlled over a 1.8V I2C interface. Over-current, over-temperature, and short-circuit protection guard the stage. It comes in a compact 2.76mm × 2.36mm 19-ball WLCSP, so you need a hot air station and a microscope to replace it. Use it to fix weak loudspeaker volume, distortion, and no sound faults on boards that carry this exact part.

15 People watching this product now!
Description

H2: AW87319 Audio IC: 8.5V Smart K Speaker Amplifier for Board-Level Repair
The AW87319 audio IC is a second-generation Smart K amplifier from Awinic that drives the loudspeaker and the receiver on smartphone mainboards. It pairs a synchronous 8.5V boost converter with a Class D output stage, so the speaker keeps its volume even as the battery voltage sags. When you see weak loudspeaker volume, crackling at high levels, or no speaker output with a healthy speaker, this amplifier belongs on your list of suspects. Mechanicpk lists it for technicians who replace the chip at board level and want exact specifications before they order.

H3: How the AW87319 Smart K audio amplifier handles volume and noise
Awinic built the chip around a synchronous boost converter that feeds a Class D power stage. The boost stage reaches up to 84% efficiency and lifts the rail to 8.5V, which lets the amplifier deliver 4.1W into an 8Ω speaker and 4.6W into a 6Ω speaker. The Triple-Level Triple-Rate AGC algorithm shapes the output so bass stays full and clipping stays out of the signal, while battery tracking AGC protects the system when cell voltage drops. Speaker noise sits at 47µV with a 102dB signal-to-noise ratio, and THD+N measures 0.015%. High PSRR of 70dB at 217Hz, TDD noise suppression, and pop-click suppression keep buzz and power-on thumps out of the speaker. In receiver mode, the Class D stage draws straight from the battery, which drops noise to 20µV for earpiece audio. You configure boost output voltage, boost peak input current, Class D gain, and the AGC parameters through registers over I2C.

H3: AW87319 audio IC in the speaker and receiver repair workflow
Check the supply and control lines before you condemn the chip. Measure VDD, which accepts 3.3V to 5.5V from the battery rail, then confirm the 1.8V-compatible I2C lines carry clean traffic. Probe the boost output at PVDD and compare it with the 8.5V target. Inspect the inductor on the SW pins, because a bad inductor or shorted boost capacitor mimics a dead amplifier. The chip carries over-current, over-temperature, and short-circuit protection, so a shorted output or overheated stage shuts the speaker down instead of burning the board. A multimeter in diode mode on VOP and VON helps you rule out a shorted speaker line first. Once the rails and I2C check out and the speaker still stays silent, the amplifier becomes the prime fault. For the swap you need a hot air station with controlled airflow, a microscope, flux, and a reballing kit.

H3: Matching the part and replacing the CSP package
Match the marking before you order. The datasheet shows the top mark as AW87319 CSR, and the package is a 19-ball WLCSP measuring 2.76mm by 2.36mm. Read the marking on your donor board under the microscope as well, because Awinic also makes related amplifiers such as the AW87318 and AW87519 with different control interfaces and packages. The AW87318 uses one-wire control and an FCQFN package, so you cannot treat it as a drop-in match. If you want a newer Smart K part, the AW87519 is a third-generation amplifier rated 4.3W at 8Ω, but only fit it when the board layout supports it. When you do an IC change karna job on this chip, clean the pads, apply fresh flux, align the balls under magnification, and test both speaker and receiver audio before you close the phone. Pair the job with your Microscopes, Hot Air Stations, and Reballing Kits to keep the pads intact.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Second-generation Smart K architecture with 8.5V synchronous boost
  • Output power of 4.1W at 8Ω and 4.6W at 6Ω
  • Triple-Level Triple-Rate AGC for fuller bass and wider dynamic range
  • Battery tracking AGC for low-voltage protection
  • Low speaker noise of 47µV, 102dB SNR, and 0.015% THD+N
  • Speaker and receiver 2-in-1 operation, receiver noise of 20µV
  • Over-current, over-temperature, and short-circuit protection
  • 2.76mm × 2.36mm CSP-19 package with 1.8V I2C control

Specifications

BrandAwinic (Shanghai Awinic Technology Co., Ltd.)
ModelAW87319 (AW87319CSR)
CategoryAudio Amplifier IC (Smart K)
CompatibilityUniversal, not device-specific. Fits any board that uses the AW87319
Technology2nd generation Smart K, Triple-Level Triple-Rate AGC, 8.5V synchronous boost, Class D
Input Voltage3.3V to 5.5V (VDD)
Power Rating4.1W at 8Ω, 4.6W at 6Ω
Dimensions2.76mm × 2.36mm (WLCSP, 19 balls)

Common Repair Uses

  • Scenarios where this exact chip is the suspect on a board that carries it.
  • Fixing weak loudspeaker volume on boards with a faulty amplifier stage
  • Restoring no sound from the speaker when the speaker itself tests good
  • Curing crackling or distortion at high volume levels
  • Repairing earpiece or receiver audio faults on 2-in-1 designs
  • Replacing the chip after a shorted speaker output trips protection
  • Diagnosing a missing 8.5V PVDD boost rail at board level
  • Reballing and replacing the WLCSP amplifier with a hot air station
  • Testing the speaker audio path after a hardware fault repair

Compatible Devices

  • Universal scope: the chip itself, not specific phone models. Check the marking on your board before ordering.
  • Smartphone mainboards with an AW87319 speaker amplifier stage
  • Boards that use AW87319 or AW87319CSR marked amplifiers
  • Designs that run speaker and receiver audio through one amplifier
  • Layouts with a 2.76mm × 2.36mm 19-ball WLCSP footprint
  • Boards with a 3.3V to 5.5V battery-fed VDD rail
  • Designs controlled over a 1.8V I2C interface
  • Single-ended or differential audio input through INP and INN

FAQ

What is the product name?
The product name is AW87319 Audio IC.
What is the brand of this product?
The brand of this product is Awinic.
What is the model of this product?
The model of this product is AW87319 (AW87319CSR).
What is this product used for?
This product is used as a Smart K speaker and receiver audio amplifier on smartphone mainboards.
Which devices are compatible with this product?
This product is universal and not device-specific. It fits any board that uses the AW87319 amplifier, so match the marking on your board before you order.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can I replace the AW87319 with an AW87318 or AW87519 on the same board?
No, treat them as different parts. The AW87319 uses I2C control in a 19-ball WLCSP, while the AW87318 uses one-wire control in an FCQFN package. Fit another model only when the board layout and software support it.
What should I check before I replace a dead AW87319 on a no sound phone?
Measure the 3.3V to 5.5V VDD rail, confirm the I2C lines are clean, and check the PVDD boost output against the 8.5V target. Also check the boost inductor and the speaker lines for shorts. Replace the chip only when these checks pass and the speaker stays silent.