AP6716M-21 Power IC for Mobile Phone RF Repair
₨ 380
Mobile Phone PA IC for Network Repair
The AP6716M-21 Power IC is a mobile phone power amplifier component from the AP6716M series, used in the RF transmit path to boost the signal before it reaches the antenna. When a handset shows no network, weak signal, or a dead transmit section, this part is one of the first suspects on the board. Mechanicpk supplies the AP6716M-21 for technicians who have confirmed the fault and need an exact replacement. Match the full suffix against the donor board, because the series includes several variants that are not interchangeable without verification.
The AP6716M-21 Power IC is a power amplifier component from the AP6716M family, the type of part that sits in the transmit chain of a mobile phone and boosts the RF signal before it reaches the antenna. In a repair workshop, this IC usually becomes relevant when a handset shows no network, drops calls, reports weak signal, or loses its transmit side after liquid damage or a power surge. For these faults, the AP6716M-21 Power IC is a targeted replacement rather than a general-purpose component, so the diagnosis must be settled before the old chip comes off the board. Mechanicpk supplies this part for workshops that already know what they are fixing and need the exact variant. Start by confirming the symptom with measurements rather than assumptions. Check the supply rails feeding the RF section with a multimeter, look for shorts to ground using a bench power supply in current-limited mode, and inspect the area around the IC under a microscope for lifted pads, burnt traces, or corroded legs. A short on a supply line can make a healthy amplifier look dead, so isolate the fault before you order a replacement. Once the amplifier is confirmed as the fault, removal and fitting fall under rework, where a dependable hot air station and a clean flux process matter more than raw speed. Removal and fitting need controlled heat. Set your hot air station to a moderate temperature, apply flux generously, and lift the IC evenly so the pads do not tear from the board. Clean the old solder from the pads with braid and flux, check neighboring pads for bridging, and then position the new part with pin one orientation confirmed against the donor layout. If the pad area has been disturbed, a reballing kit and a PCB holder keep the work repeatable. Reflow in short passes and let the board cool before the final electrical test. Variant matching is the step most often missed. The AP6716M series appears in several suffixes, including -21, -31, -51, and -61, and these are not guaranteed to be drop-in substitutes for one another across every handset. Read the marking on the removed chip, match it against the full part number, and cross-check the board revision before you fit. A mismatched variant can leave a phone that powers on but never registers on the network, which means a second visit and a dissatisfied customer. After fitting, test the phone against the original fault. Confirm that the device registers on the network, that signal holds steady during a call, and that the transmit section does not heat up in standby. Run a short stress test on the RF section if your bench allows it. Pair the replacement with the rest of your workflow: a test box for power and current monitoring, a multimeter for continuity checks, and a microscope for pad inspection. Those tools turn a single chip replacement into a repeatable service, which keeps a repair shop profitable in a competitive market. For buyers, the AP6716M-21 Power IC suits independent repair centers, service shops, and training institutes that handle mobile RF faults regularly. It fits technicians who already own a hot air station, a reballing setup, and basic test equipment. If your bench lacks rework tools, the part alone will not complete the repair, so plan the equipment before you plan the order.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Mobile phone RF power amplifier IC for the transmit path
- ✓Airoha-branded part, per distributor listings
- ✓Part of the AP6716M series, with multiple suffix variants
- ✓Targets no-network, weak-signal, and dead-transmit faults
- ✓Requires controlled hot air rework for removal and fitting
- ✓Variant matching by full part number recommended before fitting
- ✓Suited to independent repair centers and service shops
- ✓Works with standard board test equipment for post-repair verification
Specifications
| Brand Entity | Airoha |
|---|---|
| Product Entity | AP6716M-21 Power IC |
| Technology Entity | RF power amplifier IC |
| Compatible Device Entities | Mobile phone RF transmit section (device-specific list not verified) |
| Repair Process Entity | RF IC replacement, hot air rework, reballing |
| Industry Entity | Mobile phone repair parts, Pakistan repair market |
Common Repair Uses
- ✓No network or no service on the handset
- ✓Weak signal and dropped calls
- ✓Dead transmit path after liquid damage
- ✓Power surge damage in the RF section
- ✓Board-level IC replacement after short-circuit diagnosis
- ✓Reballing and reflow of the RF IC
- ✓Donor-board component swap at workshop level
- ✓Post-repair RF signal verification on test equipment
Compatible Devices
- ✓Mobile phone RF transmit section (power amplifier position). Device-specific compatibility is not verified; confirm against the donor board marking.
- ✓Mobile phone RF transmit section (power amplifier position)
- ✓Match by full part number AP6716M-21 against the donor board
- ✓Not guaranteed interchangeable with AP6716M-31, -51, or -61
- ✓Confirm board revision before fitting
- ✓Board-level IC replacement only
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is the AP6716M-21 interchangeable with the AP6716M-31 or AP6716M-51?
Does this IC need a hot air station to replace?
Related products
339S00108 WiFi IC For iPad Air iPad Pro 9.7 Replacement
In stock
358S IC T211 Samsung Tab Charging IC – Tab 3 USB Charger IC
In stock



