TI BQ25980 Charger IC – 2-Cell 8A Switched Cap DSBGA-80
₨ 450
TI BQ25980 2-Cell Fast Charge IC
The BQ25980 from Texas Instruments is an I2C-controlled switched cap parallel charger that drives 8A fast charge into a 2-cell Li-ion or Li-polymer battery at up to 98.6% peak efficiency. Its dual-phase architecture keeps cable current at half the charge current, so the phone runs cooler during high-wattage charging. The chip also carries a 7A bypass mode, a dual-input power mux controller, a 16-bit ADC, and a full protection set covering input, battery, output, and temperature faults. You get it in the original 80-ball DSBGA (YFF) package, ready for board-level replacement on 2-cell fast charge designs.
BQ25980 Charger IC: Texas Instruments 2-Cell Switched Cap Fast Charger
The BQ25980 charger IC from Texas Instruments handles the high-current fast-charge stage in devices that run a 2-cell series battery. It takes an input at twice the battery voltage and delivers twice the input current into the pack, reaching 8A of charge current at a 98.6% peak efficiency. That ratio matters on your repair bench: when a 2-cell phone charges slowly, runs hot at the port, or drops out of fast charge, the switched cap stage sits high on your suspect list. Mechanicpk supplies the BQ25980 in its original 80-ball DSBGA (YFF) package for technicians who replace charging silicon at component level instead of swapping the whole board.
Dual-Phase Switched Cap Charger Architecture and the 8A Charge Path
Unlike an inductor-based buck charger, a switched cap charger works as a fixed-ratio converter. It halves the input voltage and doubles the current, so the cable carries half the current that reaches the battery, which cuts cable loss and limits temperature rise at the connector. TI built the BQ25980 around a dual-phase version of this topology, which lifts efficiency and reduces the input and output capacitance the board needs. The chip supports battery charge voltages from 7.0V to 9.54V, the window of a 2-cell Li-ion, Li-polymer, or LiFePO4 pack. Designs that need more than 8A run two BQ25980 chips in synchronized parallel operation for up to 12A. In TI’s reference arrangement, a main charger such as the BQ25790 manages pre-charge and termination, while the BQ25980 delivers the fast-charge current. Keep that split in mind when you trace a fault: a phone that charges at a slow rate but never enters fast charge points you toward the switched cap stage before the main charger.
Bypass Mode, Dual-Input Mux, and the 16-Bit ADC
Beyond switched cap operation, the BQ25980 offers a 7A bypass mode through internal MOSFETs, with a charging path resistance under 13mΩ. Bypass mode keeps the device backward compatible with 10V fast-charging adapters on a 2-cell battery. An integrated mux controller drives external N-FETs to select between two input sources, and the chip also runs in single-input layouts with no external FET or with a single one. The operating input range reaches 22V; the input tolerates 28V without an external ACFET and 40V with one. A 16-bit ADC reports VAC voltage, bus voltage and current, output voltage, battery voltage and current, connector temperature, battery temperature, and junction temperature to the host over I2C. TI lists adapter, wireless, and power bank inputs in its application scope, so one chip can sit behind more than one charging source on the same board.
Protection Set and BQ25980 Charger IC Replacement
The protection list explains why this IC often takes the hit when a low-grade adapter or a liquid-damaged port sends a fault down the line. The BQ25980 monitors input and battery overvoltage, input and battery overcurrent, output overvoltage, input undercurrent and reverse current, input short circuit, battery and connector temperature, and junction temperature, in both switched cap and bypass modes. When one of these protections trips again and again, the phone shows a charging issue even though the battery itself tests fine. Before an IC change, check the input FETs, the connector temperature sensing line, and the battery connector, so you don’t pull a healthy BQ25980 charger IC. For the replacement itself, you work with an 80-ball DSBGA measuring 4.071 mm by 3.195 mm, with lead-free SnAgCu balls and an MSL 1 rating at a 260°C peak reflow. Use a matching stencil from your reballing kit and a controlled hot air station profile, align the chip under your microscope, and confirm I2C communication and fast-charge entry on a USB tester before you close the phone.
| Weight | 0.1 kg |
|---|
Key Features
- ✓98.6% peak efficiency dual-phase switched cap charging
- ✓8A fast charge for 2-cell batteries; 12A with two synchronized BQ25980 ICs
- ✓Cable current runs at half the battery charge current for lower heat
- ✓Integrated 7A bypass mode with sub-13mΩ charging path
- ✓Dual-input power mux controller for adapter, wireless, or power bank sources
- ✓16-bit ADC for voltage, current, and temperature telemetry over I2C
- ✓Full protection set: OVP, OCP, UCP, RCP, short circuit, and thermal monitoring
- ✓Compact 80-ball DSBGA package rated -40°C to 85°C
Specifications
| Brand | Texas Instruments |
|---|---|
| Model | BQ25980 (orderable part BQ25980YFFR) |
| Category | Battery Charger IC – Switched Cap Parallel Charger |
| Compatibility | 2-cell series Li-ion, Li-polymer, and LiFePO4 batteries |
| Supported Devices | 2-cell battery smartphones and tablets |
| Technology | Dual-phase switched cap (2:1), 7A bypass mode, I2C control, 16-bit ADC, 8A max charge current (12A with two in parallel) |
| Material | Lead-free SnAgCu solder balls, RoHS & Green |
| Input Voltage | Up to 22V operational (28V abs. max without ACFET, 40V with external ACFET) |
| Output Voltage | 7.0V – 9.54V battery charge voltage |
| Dimensions | DSBGA (YFF) 80-ball, 4.071 mm × 3.195 mm |
Common Repair Uses
- ✓Replacing a failed BQ25980 on a 2-cell board with a charging issue
- ✓Restoring fast charge when the phone only charges at a slow rate
- ✓Fixing a phone that shows charging but the battery percentage does not rise
- ✓Repairing boards after damage from a faulty or low-grade fast-charging adapter
- ✓Liquid-damage repair around the charging section
- ✓Replacing a shorted charger IC found during a hardware fault diagnosis on the input line
- ✓Resolving overheating at the charging port caused by a failing switched cap stage
- ✓Swapping a donor-board BQ25980 during board-level reconstruction
Compatible Devices
- ✓Scope verified at the battery-configuration level — the BQ25980 is not tied to a specific phone model. Match the part number on the board before replacement.
- ✓Smartphones with a 2-cell series battery and switched cap fast charging
- ✓Tablets with a 2-cell series battery
- ✓Boards pairing the BQ25980 with a main charger such as the TI BQ25790
- ✓Dual-charger boards running two BQ25980 ICs in parallel (up to 12A)
- ✓2-cell Li-ion battery designs
- ✓2-cell Li-polymer battery designs
- ✓2-cell LiFePO4 battery designs
- ✓Designs with adapter, wireless, or power bank charging inputs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the BQ25980 work alone or does it need a main charger?
What reflow temperature does the BQ25980 DSBGA package need?
Related products
339S00108 WiFi IC For iPad Air iPad Pro 9.7 Replacement
In stock
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock
A3B U2 610A3B Charging Power IC iPhone 7,7+ Tristar U4001
In stock



