D9 9-Pin Backlight IC for iPhone 6 and 6 Plus

₨ 450

D9 Backlight IC Board-Level Repair

The D9 9-pin backlight IC is a BGA-packaged control chip for the backlight boost stage on iPhone 6 and iPhone 6 Plus logic boards. It sits at the U1503 position and is identified by its D9 marking on the package. It suits jobs where the display shows an image but the backlight stays dark or dim. Replacement requires hot air rework with a 9-pin BGA profile, clean pads, and microscope-checked placement. Confirm the fault on the board before replacing, since passives on the same node can produce the same symptoms.

19 People watching this product now!
Description

D9 9-Pin Backlight IC for iPhone 6 and 6 Plus Logic Boards

The D9 9-pin backlight IC is a replacement part for the backlight boost stage on iPhone 6 and iPhone 6 Plus logic boards. It sits at the U1503 position and supplies the boosted voltage that drives the LCD backlight. When this stage fails, the handset usually boots, the touchscreen responds, and the panel stays dark or dim under a flashlight. You get the clearest picture of the fault by checking boost output before you lift anything. That keeps the diagnosis focused on the backlight path instead of the display assembly.

Fault Diagnosis on the Bench

Start by separating a backlight fault from a panel or image fault. Power the board, confirm the touch digitizer responds, and measure the backlight boost output at the U1503 node with a multimeter. A missing or low reading points toward the IC or its immediate passives. Under the microscope, check for lifted pads, cracked balls, and liquid corrosion around the package. Those signs often explain the fault without further testing. Record your readings before you remove the chip so you can compare them after reassembly.

Replacement Workflow

Remove the old IC with a hot air station set to a 9-pin BGA profile, keeping the nozzle centered to avoid heating neighboring parts. Clean the pads with flux and braid, then check them for lifting before placement. Align all nine contacts of the new D9 chip under the microscope before reflow. A single cold joint or shifted ball leaves the backlight circuit open, so inspect each joint once the board cools. Power up the board and verify the boost output before you close the job.

Where This IC Fits in Your Repair Line

This chip belongs in iPhone 6-series backlight and display work, alongside your standard board-level tools. The same hot air station, microscope, and BGA fixture setup used for power and charging IC work applies here. Many backlight faults involve the coil and filter components on the same node, so check those in the same repair pass. Stocking the D9 chip separately from full kits lets you source only what the diagnosis calls for, which keeps repair costs down for you and your customer.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Replacement for the U1503 backlight boost position on iPhone 6 and 6 Plus boards
  • BGA package for hot air rework and microscope-aligned placement
  • Addresses no-backlight and dim-display symptoms tied to the boost stage
  • Marked D9 for quick visual identification on the board
  • Suited to standard 9-pin BGA reflow and reballing procedures
  • Compact footprint for board-level repair workflows

Specifications

ModelD9 9-Pin Light IC
CategoryMobile Phone ICs
CompatibilityiPhone 6, iPhone 6 Plus
TechnologyBGA backlight boost IC
Supported DevicesiPhone 6, iPhone 6 Plus
Weight0.01 kg

Common Repair Uses

  • No-backlight faults with a working display image
  • Dim display faults traced to the boost stage
  • Board-level BGA reballing and replacement at U1503
  • Hot air rework of the backlight boost node

Compatible Devices

  • iPhone 6 logic board (U1503 position)
  • iPhone 6 Plus logic board (U1503 position)

FAQ

What is the product name?
The product name is D9 9-Pin Light IC.
What is the brand of this product?
This is an aftermarket replacement IC.
What is the model of this product?
The model is D9 9-Pin Light IC, referenced on the board as U1503.
What is this product used for?
It replaces the backlight boost IC that powers the LCD backlight on iPhone 6-series boards.
Which devices are compatible with this product?
This IC is compatible with iPhone 6 and iPhone 6 Plus logic boards at the U1503 position.
Who should use this product?
This product suits mobile repair technicians, repair shops, service centers, and professional board-repair users.
Does this IC fix a phone with no backlight but a working display image?
A faulty U1503 backlight IC typically causes this symptom, because the panel gets image data but the backlight LEDs do not receive the boosted voltage they need.
Can a cracked joint on U1503 be reflowed instead of replacing the chip?
Sometimes. A reflow can fix a cracked solder joint, but if the internal die has failed, the chip must be replaced.