ET9640 Charging IC QFN10 for Mobile Repair Pakistan
₨ 400
ET9640 Charging IC in QFN10 Package for Board-Level Repair
The ET9640 charging IC comes in a QFN10 package with a ten-pad layout and an exposed pad on the underside. Its top marking reads ET 9640 followed by a lot code. Technicians handle this part during board-level charging repairs, where the IC is checked and reworked after the charging port, cable and battery have been ruled out. Because QFN parts have no visible leads, pad alignment under magnification decides whether the replacement seats cleanly. Confirm the marking and pad count against the original part before you lift anything off the board.
ET9640 Charging IC for Board-Level Charging Repair
The ET9640 is a QFN10 charging IC supplied in a ten-pad package with an exposed thermal pad on the underside. The top marking reads ET 9640 with a second line of characters, which is most likely a lot or date code. This listing covers only the package and marking, because those are the details that can be checked physically on the chip. Before you order or fit this part, match the marking and pad count against the IC on your board.
Package and Marking Check
Start by reading the top marking under your microscope and comparing it with the original IC on the board. The first line reads ET, and the second reads 9640. The third line is a lot or date code and does not need to match exactly for a replacement, but the main marking should. Count the ten pads on the underside and check that the exposed pad is present in the same position as the original part. A pad count or orientation mismatch on a QFN package causes shorts or a dead charging line, so check it before you reflow.
Preparing the Board Site
Map the orientation of the old IC with a photo before removal. Use hot air at a moderate, even temperature to lift the old part without lifting adjacent pads. Clean the site and re-tin the pads with fresh flux and solder so the new part seats evenly. Avoid excess solder, because a bridge between the exposed pad and a neighbouring pad creates a short that is hard to spot after reflow.
Placement and Reflow
Align the new IC carefully under magnification. QFN packages have no visible leads, so the pads and exposed pad must line up with the board footprint. A small offset shows up as a bridge or a dead line after reflow. Once the part sits square, reflow it with a steady, even heat until the solder wets all ten pads and the exposed pad.
Testing After Replacement
Check the charging line for shorts to ground with a multimeter before you apply power. Then test with a known-good cable and charger and watch the board for several minutes. Check temperature at the IC site as well, since a board that heats up quickly after reflow may point to a bridge or a damaged part.
| Weight | 0.1 kg |
|---|
Key Features
- ✓QFN10 package with ten pads
- ✓Exposed thermal pad on the underside
- ✓Top marking ET 9640 for identification
- ✓Suited to hot air rework with fine pad alignment
Specifications
| Category | Charging IC |
|---|---|
| Model | ET9640 |
| Package | QFN10 |
Common Repair Uses
- ✓Board-level charging IC replacement after the port, cable and battery have been ruled out
- ✓Checking and reworking a QFN charging IC site with hot air
- ✓Verifying a suspect charging line with a multimeter before and after reflow
Compatible Devices
- ✓Universal, not device-specific. Confirm the marking and pad layout against the board before replacing.
- ✓Universal (not device-specific), verified by package and marking only
- ✓Boards where the original part is marked ET 9640
- ✓QFN10 footprint boards with a matching ten-pad and exposed-pad layout
FAQ
What is the product name?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What package is the ET9640 supplied in?
How do I confirm the ET9640 matches my board before replacing it?
Related products
358S IC T211 Samsung Tab Charging IC – Tab 3 USB Charger IC
In stock
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock
U2 Charging iPhone 8, iPhone 8 Plus, iPhone X Chip – 1612A1
In stock



