Flash 64 Ultra Tool Box full set – UFS eMMC ISP Programmer
₨ 183,000
UFS and eMMC Programming Kit for Mobile Repair
The Flash 64 Ultra Tool Box full set brings managed NAND programming into one kit for technicians who service UFS and eMMC storage. It includes BGA socket adapters for UFS 153, UFS 254 and UFS 297 packages, an eMMC 4-in-1 BGA adapter, and ISP V2 cabling for in-system programming. The vendor rates transfer speeds up to 420 MB/s with UFS 3.x and UFS 4.x devices. The software runs on Windows 8, 10 and 11, so the kit fits a standard repair bench PC.
In stock
The Flash 64 Ultra Tool Box full set is a UFS eMMC ISP programmer kit for technicians who handle managed NAND storage in smartphones, and it places the sockets, adapters and cables you need in one box. Boot loop issue cases, dead phone repairs and dead after flash boards usually depend on reading or rewriting the storage chip directly, so the correct socket for each package matters as much as the software. This set covers the common UFS BGA packages through separate 153, 254 and 297 adapters, and it adds an eMMC 4-in-1 BGA adapter for eMMC chips. The vendor describes a dual-core SoC and ASIC design rated for transfer speeds up to 420 MB/s with UFS 3.x and UFS 4.x devices, which saves time when you read large partition images. For chips that stay on the board, the ISP V2 adapter and the flex cable sets, including the UFS HSG1 FPC V2 cable and the eMMC FPC V2 cable, provide a connection path without desoldering. The software runs on Windows 8, Windows 10 and Windows 11, and it works at two access levels. High-level access lets you read and write Android OS partitions, which covers most firmware recovery jobs. Low-level access reaches raw partitions, logical units and RPMB areas, which is where deeper faults get handled. For UFS work, you can access and configure descriptors, attributes and flags, which helps when an IC needs a correct setup before it boots. For eMMC work, you get full access to the Extended CSD register, which supports deep customization and low-level repartitioning when a standard write does not restore the chip. Nano memory cards and MicroSD cards are also supported, which extends the kit beyond phones. The same package styles appear in TV boxes, game consoles and IoT devices, so the kit suits those repair jobs as well. A typical job starts by identifying the storage package, then selecting the matching adapter, then reading the device ID and comparing it with a known good image. Each step depends on correct socket seating, so check pad alignment under a microscope before you power the board. Hardware faults and software faults look alike on a dead phone, and the programmer helps you separate them. If the chip reads cleanly and the partitions look intact, the fault likely sits on the board, in the power rails, charging ICs or the processor. If reads fail, the storage or its connection becomes the suspect, and a fresh socket seat or a reballing step may restore it. Pair the programmer with a hot air station for chip removal, a microscope for pad inspection and a PCB holder during reballing and reflow. For boards that need pinout reference or power checks, add an ISP pinout tool and a test box to the same bench to shorten diagnosis time. Before you write anything, confirm the chip package, read the ID and save an original dump, because socket mismatch is the most common reason a UFS or eMMC read fails on the first attempt. A saved dump gives you a rollback point if the new image fails. Treat the vendor speed figure as a ceiling under ideal conditions rather than a guaranteed rate. This kit suits repair shops, service centers and training institutes that handle managed NAND daily, and it delivers a single-box answer for UFS, eMMC and ISP workflows without juggling loose adapters.
| Weight | 1.0 kg |
|---|
Key Features
- ✓UFS BGA socket adapters for 153, 254 and 297 packages
- ✓eMMC 4-in-1 BGA socket adapter
- ✓ISP V2 adapter with flex cable set
- ✓UFS HSG1 FPC V2 cable and eMMC FPC V2 cable
- ✓High-level read and write of Android OS partitions
- ✓Low-level access to raw partitions, logical units and RPMB
- ✓UFS descriptor, attribute and flag configuration; eMMC Extended CSD access
- ✓Vendor-rated transfer speed up to 420 MB/s, Windows 8, 10 and 11 support
Specifications
| Brand Entity | Flash 64 (F64) programmer line |
|---|---|
| Product Entity | Flash 64 Ultra Tool Box full set |
| Technology Entity | UFS 3.x and UFS 4.x managed NAND, eMMC Extended CSD, ISP V2 programming |
| Compatible Device Entities | UFS BGA 153, 254 and 297 packages; eMMC managed NAND; Nano and MicroSD cards |
| Repair Process Entity | Managed NAND reading, writing and partition recovery |
| Industry Entity | Mobile phone repair, IC-level repair, data recovery, flashing and programming |
Common Repair Uses
- ✓Recovering data and reflashing partitions on phones with boot loop issues
- ✓Re-flashing corrupted modem or system partitions on managed NAND
- ✓Reading and writing Android OS partitions at high level
- ✓Configuring UFS descriptors, attributes and flags during IC setup
- ✓eMMC repartitioning and Extended CSD changes for low-level repair
- ✓In-system programming through ISP V2 cabling when the chip stays on the board
- ✓Managed NAND work in TV box, game console and IoT repair
Compatible Devices
- ✓UFS 3.x managed NAND ICs in BGA 153, 254 and 297 packages (vendor listed)
- ✓UFS 4.x managed NAND ICs (vendor listed)
- ✓eMMC managed NAND ICs through the 4-in-1 BGA adapter
- ✓Nano memory cards and MicroSD cards
- ✓Universal scope, not limited to specific phone models
FAQ
What is the product name?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Which UFS BGA sockets are included in this kit?
Which Windows versions can run the software?
Related products
UFI UFS-Prog UFS and eMMC Programmer for Mobile Repair
In stock



