Cirrus Logic LN8000 Charging IC – Fast Charging PMIC
₨ 350
LN8000 Charging IC for Fast-Charge Board Repair
The LN8000 charging IC is a high-efficiency master charger from Cirrus Logic, which came from Lion Semiconductor’s fast-charging line. Distributors list it as a PMIC battery charger IC. It sits in the battery charging stage of the board, so a failed unit usually shows up as a charging issue, heating near the battery section, or fast charge not working. Xiaomi Pad 5 boards use this part, and you will also find it on other devices built around the same fast-charge design. Before you start the IC change, check the marking on the board you are repairing. The IC is RoHS3 compliant and suits a lead-free rework workflow on your repair bench.
LN8000 Charging IC: What It Does on the Board
The LN8000 charging IC handles high-efficiency battery charging on fast-charge mobile and tablet boards. Lion Semiconductor designed it, and Cirrus Logic now owns it after acquiring Lion in 2021. Lion built its fast-charging parts on switched-capacitor architecture. Those parts sit close to the battery and give better efficiency and heat handling than older charging designs, which is why many flagship and mid-range phones adopted them. Distributors list the LN8000 under PMIC battery chargers and describe it as a master charger with high efficiency. When this IC fails, the phone often stops fast charging, heats up near the battery area, or shows no charging at all. Your diagnosis needs to confirm the fault at this stage before you lift the chip.
Where the Cirrus Logic LN8000 Fits in Your Repair Workflow
This IC belongs to the power and charging section, not the main PMIC area. That difference matters during diagnosis. A charging issue can come from the charging port, the flex, the battery connector, the main PMIC, or a fast-charge stage like the LN8000. Start with a DC power supply and watch current draw while you connect a charger. Then use your multimeter in diode mode to check the lines around the IC for a short to ground. If a line shows a short, use a thermal camera or freeze spray to find the part that heats up. When the heat points to the LN8000 itself, the IC change becomes the right move. The Xiaomi Pad 5 is a confirmed platform for this part, since the open-source mainline kernel for that tablet enables an LN8000 charger. On other boards, match the marking on the chip and check the schematic before you order a replacement.
LN8000 Fast Charging IC Replacement Steps
The removal and refitting process follows standard IC rework practice. Lead-free solder comes standard on modern boards, and this part carries RoHS3 compliance, so set your hot air station for lead-free work. Shield nearby components, especially the battery connector and any underfill-sensitive chips, with Kapton tape. Add fresh flux, heat evenly, and lift the IC straight up without forcing it. Clean the pads with solder wick and flux, and check every pad under a microscope for lifted or torn pads. If the old IC came off with balls attached to the board, re-level the pads before placing the new chip. Use a reballing stencil if the new IC needs fresh balls. Align the chip with the board marking, apply heat, and let the solder settle the part into position. After cooling, clean the area and test charging current with a USB tester before you close the device.
Tools You Need Alongside This Charging IC
A clean LN8000 replacement depends on a controlled bench setup. You need a hot air station with stable temperature, a soldering station with a fine tip for pad cleanup, a microscope for pad inspection, and a good flux. A PCB holder keeps the board flat so heat spreads evenly. A DC power supply and a multimeter cover the diagnosis side, and a thermal camera speeds up short finding. For shops that handle many charging faults each week, an upgraded hot air station with airflow control gives you better results on small charging ICs without disturbing nearby parts.
Buying the Right Part
Cirrus Logic sells other charging ICs with similar names, such as the LN8282, which carries a different voltage and current rating. Order the exact LN8000 marking that your board carries. Never swap in a similar-looking part number, because each IC in this family has its own ratings and firmware configuration on the board. The correct part, fitted with clean rework, gives you a reliable fast-charging repair that your customer can trust.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Original Cirrus Logic part number, LN8000
- ✓Belongs to Lion Semiconductor’s fast-charging IC family
- ✓High-efficiency master charger design
- ✓Classified as a PMIC battery charger IC
- ✓RoHS3 compliant, suited to lead-free rework
- ✓Fitted in the Xiaomi Pad 5 charging circuit
- ✓Direct replacement for a failed LN8000 on matching boards
- ✓Fits standard hot air IC change and reballing workflows
Specifications
| Brand | Cirrus Logic (originally Lion Semiconductor) |
|---|---|
| Model | LN8000 |
| Category | PMIC – Battery Charger IC |
| Compatibility | Boards using the LN8000 fast-charging stage; Xiaomi Pad 5 confirmed |
| Supported Devices | Xiaomi Pad 5 |
| Technology | High-efficiency master charger from Lion Semiconductor’s switched-capacitor fast-charging line; RoHS3 compliant |
Common Repair Uses
- ✓Charging-section board repairs where diagnosis points to the LN8000.
- ✓Fast charging not working while normal charging stays active
- ✓Charging IC heating or shorting to ground
- ✓No charging after using a faulty or high-voltage adapter
- ✓Charging section repair after liquid damage
- ✓Pad repair and IC change after a failed previous rework
- ✓Replacement during charging-section board swaps or donor board repairs
Compatible Devices
- ✓Verified at device level for Xiaomi Pad 5; for any other board, match the chip marking before replacing.
- ✓Xiaomi Pad 5 (nabu)
- ✓Any phone or tablet board that carries the LN8000 marking in its charging section
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I replace the LN8000 with the LN8282 or another Cirrus Logic charging IC?
How do I confirm the LN8000 is faulty before doing an IC change?
Related products
A3B U2 610A3B Charging Power IC iPhone 7,7+ Tristar U4001
In stock



