SKY77643-21 PA IC – 3G/4G Multiband Power Amplifier

₨ 450

Skyworks SKY77643-21 Multiband PA Module

The SKY77643-21 PA IC is a Skyworks SkyLiTE multimode multiband power amplifier module built for 3G and 4G handset front ends. It drives transmit power across WCDMA, TD-SCDMA, FDD-LTE and TDD-LTE bands, and the baseband controls it fully through MIPI. The 42-pad MCM package measures 4.0 × 6.8 × 0.8 mm and has internal 50-ohm matching, so the replacement footprint stays clean. Use it to replace a failed PA stage on boards with no network, outgoing calls that drop, or a shorted supply line around the RF section. It suits technicians who do board-level network repair and need the exact -21 variant.

13 People watching this product now!
Description

SKY77643-21 PA IC for 3G and 4G Network Repair

The SKY77643-21 PA IC is the power amplifier stage in Skyworks’ SkyLiTE family. It handles the transmit side of a 3G/4G handset front end. Sometimes a phone shows signal bars but drops every outgoing call, or it loses network the moment it tries to register. In those cases the PA stage is one of the first places to check. This module amplifies the transceiver’s RF output across WCDMA, TD-SCDMA, FDD-LTE and TDD-LTE bands, then switches it internally to the correct output path. Mechanicpk stocks the exact 42-pad -21 variant for technicians who do board-level network repair and don’t want to fit a guessed substitute.

Inside the SkyLiTE Module Architecture

Skyworks builds the module on a multi-layer laminate substrate. The substrate carries an InGaP amplifier die, a silicon CMOS control die and passive components, all inside one 42-pad MCM surface-mount package. The package measures at most 4.0 × 6.8 × 0.8 mm. The CMOS die runs the MultiFunction Control block over standard MIPI commands, so the baseband sets bias modes, band selection and output routing in software instead of through separate control lines. Internal 50-ohm matching on the RF ports reduces the number of external components around the footprint. The module offers two T/R ports and 14 outputs. Its dual low-band inputs let the board designer feed it from separate transceiver outputs or through an interstage filter. Leakage current stays very low, which protects standby time. Keep this in mind when you trace a battery drain complaint back to the RF section.

Band Coverage and Modulation Support

This Skyworks power amplifier module covers:

  • WCDMA bands I, II, III, IV, V, VIII and IX
  • TD-SCDMA bands 34 and 39
  • FDD-LTE bands 1, 2, 3, 4, 5, 7, 8, 9, 12, 13, 17, 20, 28 and 30
  • TDD-LTE bands 38, 39, 40 and 41

That range includes the 2100 MHz WCDMA band and the 1800 MHz LTE band 3 that local networks rely on heavily. On 3G it handles WCDMA Release 99 voice, HSDPA, HSUPA, HSPA+ and TD-SCDMA modulation. On LTE it supports channel bandwidths of 1.4, 3, 5, 10, 15 and 20 MHz. A DCDC converter adjusts VCC through average power tracking, which keeps efficiency high at every output level. MIPI-programmable bias modes let the platform trade efficiency against linearity for each mode, and Skyworks rates its 3G/4G power-added efficiency as industry-leading for this class.

Diagnosing a Faulty 77643-21 Network IC

PA faults usually show up as a “network issue”: emergency calls only, network that comes and goes, call drops on transmit, or 4G data that won’t connect even though the SIM reads fine. A shorted PA can also pull its supply line to ground, causing heating near the RF shield or a dead phone. Start with a multimeter in diode mode on the PA supply line and compare the reading against a known-good board. If the line reads short, inject a low voltage and use rosin or a thermal camera to confirm the PA is the hot component and not a nearby capacitor. Check the marking on the old module before you order. SKY77643-11 is a separate Skyworks variant, so confirm the -21 suffix.

Replacing the SKY77643-21 PA IC on Your Bench

Clamp the board in a PCB holder and remove the RF shield. Lift the old module with a hot air station at a controlled temperature, using a preheater on multilayer boards to protect nearby BGA chips. Clean the pads with flux and wick. Inspect them under a microscope for lifted pads or bridged ground pads, then align the new module by its pin-1 marker and reflow evenly. After reassembly, confirm network registration, place a test call and run a 4G data session to check that the transmit path works on every band the phone uses. For heavy RF board work, a stereo microscope with a reflow-ready preheater gives you better control on 42-pad modules.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Multimode multiband PAM covering WCDMA, TD-SCDMA, FDD-LTE and TDD-LTE
  • 14 FDD-LTE bands and 4 TDD-LTE bands supported
  • Fully programmable MIPI control interface
  • Two T/R ports and 14 RF outputs
  • Dual low-band RF inputs for separate transceiver outputs or interstage filtering
  • Optimized for APT DCDC operation for high efficiency at every power level
  • Internal 50-ohm matching reduces external components
  • Low-profile 42-pad MCM package, 4.0 × 6.8 × 0.8 mm max

Specifications

BrandSkyworks Solutions
ModelSKY77643-21
CategoryMobile Phone ICs > Power Amplifier (PA) ICs
Compatibility3G/4G multimode multiband handset front ends with MIPI control
Supported DevicesMultiband 3G/LTE handsets (WCDMA, TD-SCDMA, FDD-LTE, TDD-LTE)
TechnologySkyLiTE MMMB PAM, InGaP amplifier die with CMOS MIPI control, APT DCDC-optimized
MaterialInGaP and silicon dies on a multi-layer laminate substrate, encapsulated MCM
Dimensions4.0 × 6.8 × 0.8 mm (max), 42-pad SMT package

Common Repair Uses

  • No network / emergency calls only fault
  • Outgoing call drops while signal bars still show
  • 4G/LTE data not connecting on a known-good SIM
  • 3G network loss on WCDMA bands
  • Shorted PA supply line pulling VBAT to ground
  • Heating near the RF section after water damage
  • Dead phone traced to a shorted PA module
  • Post-drop RF section repair after physical board damage

Compatible Devices

  • These are verified band and platform coverage. I couldn’t confirm specific phone models.
  • 3G/4G multiband smartphones with a MIPI-controlled RF front end
  • WCDMA Bands I, II, III, IV, V, VIII, IX handsets
  • TD-SCDMA Bands 34 and 39 handsets
  • FDD-LTE Bands 1, 2, 3, 4, 5, 7, 8, 9 devices
  • FDD-LTE Bands 12, 13, 17, 20, 28, 30 devices
  • TDD-LTE Bands 38, 39, 40, 41 devices
  • Boards that use the SKY77643-21 module footprint (42-pad MCM)
  • Direct replacement only for an original SKY77643-21 marking (not the -11 variant)

FAQ

What is the product name?
The product name is SKY77643-21 PA IC – 3G/4G Multiband Power Amplifier.
What is the brand of this product?
The brand of this product is Skyworks Solutions.
What is the model of this product?
The model of this product is SKY77643-21.
What is this product used for?
This product is used for replacing a faulty 3G/4G power amplifier stage on mobile phone boards with network, signal or transmit faults.
Which devices are compatible with this product?
This product is compatible with 3G/4G multiband handsets that use the SKY77643-21 module, covering WCDMA, TD-SCDMA, FDD-LTE and TDD-LTE bands under MIPI control.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can I use SKY77643-11 instead of SKY77643-21?
Skyworks lists SKY77643-11 and SKY77643-21 as separate variants, so replace a -21 module only with a -21 part to avoid band or control mismatches.
Which LTE bands does the SKY77643-21 PA IC support?
It supports FDD-LTE bands 1, 2, 3, 4, 5, 7, 8, 9, 12, 13, 17, 20, 28 and 30 and TDD-LTE bands 38, 39, 40 and 41, with channel bandwidths from 1.4 to 20 MHz.