MT6365VMW Power IC – MediaTek 203-Ball WFBGA PMIC
₨ 300
MediaTek MT6365VMW Power IC for Dimensity 900 Boards
The MT6365VMW Power IC is MediaTek’s main power management chip for MT6877V (Dimensity 900) smartphone boards, including the Infinix Zero 5G (X6815). One 203-ball WFBGA package holds 9 buck converters, 33 LDOs, a full audio codec, an RTC and a fuel gauge, so this single IC decides whether the board boots at all. Technicians replace it when a phone shows a VBAT short, no current draw, missing core rails, or storage and audio faults that trace back to the PMIC. Mechanicpk supplies the exact MT6365VMW marking for clean board-level replacement.
MT6365VMW Power IC: The Main PMIC Behind Dimensity 900 Boards
The MT6365VMW power IC sits between the battery line and the MediaTek SoC and builds nearly every rail the board needs to start: processor, GPU, modem, memory, storage, SIM, camera I/O and audio. MediaTek pairs it with the MT6877V (Dimensity 900) application processor, and the Infinix Zero 5G (X6815) uses it alongside the MT6315 sub-PMIC and MT6360 charger IC. When this chip fails, you typically get a dead phone with zero current, a hard short on VBAT, or a set that powers up and hangs on logo. Mechanicpk stocks the exact MT6365VMW marking for technicians who work at BGA level and need a direct match, not a near substitute from the same family.
Inside the MediaTek MT6365 PMIC: Rails, Codec and Control
The MT6365 family packs 9 buck converters and 33 LDOs into a 203-ball WFBGA body measuring 5.98 × 5.62 mm. The bucks carry the heavy loads, including VPROC1, VPROC2, VCORE, VGPU, VMODEM and VS1/VS2. The LDOs feed lighter rails such as VEMC and VUFS for storage, VSIM1 and VSIM2 for the SIM slots, VUSB, VIO18, VIO28 and VCAMIO. The chip also integrates an uplink/downlink audio codec with earpiece, headset and microphone bias outputs, a crystal-less 32K RTC, clock buffers for the SoC, cellular RF, connectivity and UFS, and a fuel gauge with current sensing. The SoC controls everything over SPI plus two SRCLKEN lines. Protection covers over-current, thermal shutdown at 150 °C, and under-voltage and over-voltage lockout. This level of integration explains why one failed MT6365VMW can mimic CPU, eMMC/UFS, audio or network faults.
Diagnosing an MT6365VMW Power IC Fault on the Bench
Start with a DC power supply and watch the current when you press the power key. A direct short on VBAT that heats the PMIC area under rosin or a thermal camera points to an internal failure, because the buck inputs connect straight to the battery line. If current stays at zero, check the PWRKEY line and VSYS at the IC before you condemn the chip. A partial boot, where current climbs and then drops, calls for measuring each buck output at its inductor; a missing VCORE or VPROC rail with a healthy load usually confirms the PMIC. Check VEMC and VUFS when the phone goes dead after flash or the storage stops responding, and check the audio outputs when earpiece and microphone fail together. On Infinix Zero 5G boards, rule out the MT6360 charger IC and MT6315 sub-PMIC first, since their faults overlap with main PMIC symptoms.
Replacement Workflow for the MT6365VMW Power IC
Secure the board in a PCB holder and shield nearby plastic parts and connectors. If the board uses underfill glue, soften and clear it before you lift the chip. Use a bottom preheater with your hot air station so the board heats evenly and the surrounding passives stay in place. After removal, clean the pads with desoldering wick and low-melt solder, then inspect for lifted or torn pads under a microscope. Reball the new IC with a matching stencil from a BGA reballing kit, align it by the ball-1 marker, and reflow with plenty of flux. Let the board cool naturally. Before you close the phone, power it from the DC supply, confirm a normal boot current pattern, and measure the key rails with a multimeter. For the next step up in board repair, pair this IC with a thermal camera to locate shorts in seconds instead of minutes.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Exact MediaTek MT6365VMW marking for direct board-level replacement
- ✓9 buck converters for processor, GPU, core, modem and system rails
- ✓33 LDOs covering storage, SIM, USB, I/O and camera rails
- ✓Integrated uplink/downlink audio codec with headset and earpiece outputs
- ✓Crystal-less 32K RTC with clock buffer outputs for SoC, RF and UFS
- ✓Fuel gauge with current sensing for accurate battery reporting
- ✓Over-current, thermal shutdown and voltage lockout protection
- ✓203-ball WFBGA package (5.98 × 5.62 mm) for BGA rework
Specifications
| Brand | MediaTek |
|---|---|
| Model | MT6365VMW |
| Category | Power Management IC (PMIC) |
| Compatibility | MediaTek MT6877V (Dimensity 900) smartphone platform |
| Supported Devices | Infinix Zero 5G (X6815) |
| Technology | 9 buck converters, 33 LDOs, integrated audio codec, 32K crystal-less RTC, fuel gauge, SPI control |
| Input Voltage | 2.6 V – 5 V |
| Dimensions | 203-ball WFBGA, 5.98 × 5.62 mm |
Common Repair Uses
- ✓Dead phone with no current draw on DC power supply
- ✓VBAT or VSYS short traced to the main PMIC
- ✓Phone hangs on logo or restarts in a boot loop due to unstable core rails
- ✓Missing VCORE, VPROC or VGPU output after confirming a healthy load
- ✓Storage not detected or dead after flash due to missing VEMC/VUFS rail
- ✓No SIM detection traced to VSIM1/VSIM2 output
- ✓Earpiece, headset and microphone failing together due to codec section fault
- ✓Replacement after liquid damage or overheating on the PMIC area
Compatible Devices
- ✓Verified board-level scope; match the MT6365VMW marking on the board before ordering
- ✓Infinix Zero 5G (X6815)
- ✓MediaTek MT6877V (Dimensity 900) boards that carry MT6365VMW as the main PMIC
- ✓Boards pairing MT6365VMW with MT6315 sub-PMIC and MT6360 charger IC
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I replace MT6365VMW with MT6365IAW or MT6365IBW?
Can a faulty MT6365VMW cause a VBAT short on a dead Infinix Zero 5G?
Related products
358S IC T211 Samsung Tab Charging IC – Tab 3 USB Charger IC
In stock



