MT6368DW Power IC MediaTek PMIC for Dimensity 8100 Boards
₨ 450
H2: MediaTek MT6368DW PMIC for Board-Level Power Repair
The MT6368DW power IC is a MediaTek power management chip that sits on the Redmi Note 11T Pro mainboard, a board built around the Dimensity 8100 platform. It generates the regulated rails that the processor and surrounding circuits need to start and run. When this chip fails, you see a dead phone, a shorted supply rail, or a board that never completes its power-on sequence. Mechanicpk supplies the exact MT6368DW marking for technicians who replace PMICs at component level. Pair it with a reballing stencil, a hot air station and a microscope, and you have everything the job needs.
H2: MT6368DW Power IC for Dimensity 8100 Board-Level Repair
The MT6368DW power IC is a MediaTek power management chip that Xiaomi mounts on the rear side of the Redmi Note 11T Pro mainboard, part of a Dimensity 8100 board design. It belongs to MediaTek’s multi-function PMIC line, the chips that turn battery voltage into the separate regulated rails the processor, memory and peripherals draw from. When it fails, the phone usually reaches your bench as a dead phone, a board with a shorted rail, or a unit stuck in a boot loop issue. Mechanicpk stocks the bare MT6368DW chip for technicians who repair at component level, so your IC change karna job starts with the exact marking the board expects.
H3: Inside the MediaTek Power Architecture
MediaTek splits power delivery on its 5G platforms across several dedicated chips instead of one regulator block. MediaTek’s kernel sources carry a separate multi-function driver for the MT6368 family, which tells you the chip handles far more than a single voltage output. On Dimensity 8100 hardware, the MediaTek MT6368DW PMIC shares the board with other MediaTek power chips, and you need to know which one actually failed before you touch the hot air. The AMAOE Mi16 Xiaomi stencil groups the MT6368DW with the MT6373AW, MT6375P and MT6319AP ball patterns, a useful hint about how many PMICs live on this board family. Treat the part number as exact. MediaTek ships several suffix variants under one base number across its PMIC families, and a different suffix can carry a different boot-up voltage configuration. Match the full MT6368DW marking printed on the original chip and confirm it against the board before you order a replacement.
H3: Diagnosing a Faulty MT6368DW Power IC
Start on a DC power supply instead of the battery. Connect the board, press power, and watch the current reading. A heavy draw the moment you connect points toward a shorted rail, while a board that draws nothing at all suggests the power-on sequence never starts. Neither reading alone condemns the PMIC, so trace further. Switch your multimeter to diode mode and compare the rails around the MT6368DW against a known-good board or your schematic. When a rail reads near zero, inject low voltage and find the heat source with rosin smoke or a thermal camera. If a decoupling capacitor heats up, replace the capacitor first, because that fix costs you minutes. If the PMIC body heats up, you have a confirmed hardware fault inside the chip. Boards from a drop or a liquid-damaged phone can also show cracked joints under this chip, so inspect the edges under a microscope before you choose between a reball and a full replacement.
H3: Replacing the Chip on Your Repair Bench
Lock the board in a PCB holder and run a preheater underneath so the multilayer board stays flat during removal. If the board carries underfill around the PMIC, soften it with heat and clear it with a fine blade before you lift the chip, or the pads will tear away with it. Use your hot air station with plenty of flux, lift the old chip straight up, then level the pads with solder wick and clean off the residue. Reball the new MT6368DW power IC with the matching stencil, align the marking and pin-one dot with the board, and reflow until the chip settles and self-centres. Check alignment under your microscope before the board cools fully. Put the board back on the DC power supply and confirm a normal current pattern before full assembly. If you handle PMIC jobs every week, a board preheater with even bottom heat is the upgrade that cuts lifted pads more than any other tool change.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Exact MT6368DW marking for direct board-level replacement
- ✓MediaTek multi-function power management IC
- ✓Matches the PMIC on the Redmi Note 11T Pro mainboard
- ✓Built for the Dimensity 8100 smartphone platform
- ✓BGA chip that reballs with the AMAOE Mi16 Xiaomi stencil
- ✓Bare chip for component-level repair, not a board module
- ✓Restores regulated power rails after a confirmed PMIC fault
- ✓Suits hot air rework with preheater and flux workflow
Specifications
| Brand | MediaTek |
|---|---|
| Model | MT6368DW |
| Category | Power Management IC (PMIC) |
| Compatibility | Redmi Note 11T Pro mainboard (Dimensity 8100 platform) |
| Supported Devices | Boards carrying the MT6368DW marking |
| Technology | Multi-function smartphone power management IC, BGA reball mounting |
Common Repair Uses
- ✓Component-level PMIC diagnosis and replacement on MediaTek boards.
- ✓Dead phone with no current draw on the DC power supply
- ✓Supply rail short traced to the PMIC body by thermal check
- ✓Boot loop issue or hang on logo after a PMIC rail failure
- ✓Liquid-damaged board with corroded PMIC joints
- ✓Drop-damaged board with cracked solder joints under the PMIC
- ✓Replacing a PMIC overheated during a previous rework attempt
- ✓Reball and reseat of a lifted PMIC
- ✓Donor-to-board PMIC transfer on Dimensity 8100 boards
Compatible Devices
- ✓Verified at device level for the Redmi Note 11T Pro; at platform level for Dimensity 8100 boards that carry the identical marking.
- ✓Xiaomi Redmi Note 11T Pro (MT6368DW confirmed in mainboard teardown)
- ✓MediaTek Dimensity 8100 (MT6895) board designs using the MT6368DW
- ✓Any phone board where the original PMIC reads MT6368DW in full
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I use another MT6368 suffix in place of the MT6368DW?
Which stencil reballs the MT6368DW power IC?
Related products
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock
358S IC T211 Samsung Tab Charging IC – Tab 3 USB Charger IC
In stock



