Qualcomm PMI8937 Power IC – Charging PMIC for MSM8937

₨ 400

PMI8937 Charging IC for Snapdragon 430 Board Repair

The Qualcomm PMI8937 is the interface power management IC that sits beside the PM8937 on MSM8937 (Snapdragon 430) motherboards. It runs the battery charger, fuel gauge, LED drivers and PWM functions, and it alone receives the VBUS and USB_ID lines from the charging port. When a board shows no charging, false charging, or a dead phone after a short at the port, this IC often carries the fault. You get a genuine replacement part for IC-level repair, ready for hot air rework on a professional repair bench anywhere in Pakistan.

20 People watching this product now!
Description

Qualcomm PMI8937 Power IC: The Charging and Interface PMIC for MSM8937

The PMI8937 power IC is Qualcomm’s interface PMIC for the MSM8937 platform, better known as Snapdragon 430. Qualcomm splits power duties across two chips on this platform. The PM8937 handles the main regulators, while the PMI8937 takes charge of the battery side: the charger, the fuel gauge, LED drivers and PWM outputs. Both chips talk to the CPU over the SPMI bus, the System Power Management Interface that Qualcomm uses across its mid-range designs. For a technician, that split matters. A board that boots on a DC power supply but refuses to charge usually points away from the PM8937 and straight toward the PMI8937 and its surrounding components.

How the PMI8937 Controls the Charging Path

Trace the charging circuit on an MSM8937 board and you find a key detail: the VBUS and USB_ID lines from the charging port route only to the PMI8937, not to the CPU. The PMI8937 detects the charger type itself and then reports plug and unplug events to the USB software layer. The qpnp-smbcharger driver sets the charging parameters, and the IC’s hardware state machine regulates the actual charging current. In practice, a damaged PMI8937 can block charger detection entirely. The phone shows no charging icon, the ammeter on your DC supply stays flat, and a new charging port changes nothing. Because the IC sits directly on the VBUS path, a faulty charger or a voltage spike at the port often hits it first.

Beyond charging, the PMI8937 runs the fuel gauge that reports battery percentage, along with the LED and PWM drivers. A partial failure can show up as a battery percentage that jumps or freezes, while the phone still boots normally on battery.

Diagnosing a PMI8937 Fault Before You IC Change Karna

Confirm the fault before you lift anything. Start with the charging port and its flex, then measure VBUS on the board side with a multimeter. If VBUS reaches the board but the phone never registers a charger, check the PMI8937 area for shorts in diode mode and look for heat with a thermal camera or rosin. A shorted VBUS line that warms the PMI8937 power IC during DC injection gives you a strong signal. Inspect the chip under a microscope for corrosion, especially on liquid-damaged boards, since moisture near the charging port often reaches this section. Rule out the battery connector and fuel gauge sense lines as well, because a wrong battery reading can mimic a charging issue. Compare the IC marking against the board too: MSM8937 boards pair the PMI8937 with a PM8937, while other Qualcomm platforms use different interface PMICs, so the part number on the chip decides your replacement.

Rework Process and the Bench Tools You Need

Plan the removal carefully, especially if the board uses underfill around the IC. Preheat the PCB on a preheater or PCB holder with bottom heat, then soften any underfill with controlled hot air before you lift the chip. Clean the pads with flux and wick until every pad stays flat and intact, since one lifted pad on the VBUS or battery lines ends the repair. Reball the new IC with the matching stencil from a BGA reballing kit, align it under a microscope, and reflow with steady airflow so you don’t disturb nearby passives. After rework, power the board from a DC power supply before you connect a battery. Watch the current draw, plug in a charger, and confirm the board detects it. A clean current climb on charger insertion tells you the PMI8937 and the charging path work again. Keep a hot air station, soldering station, multimeter and microscope on the same bench for this job; for high-volume IC work, a stereo microscope with a stable boom stand makes the natural upgrade.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Qualcomm interface PMIC for the MSM8937 platform
  • Integrated battery charger control
  • Built-in fuel gauge for battery state of charge
  • LED and PWM driver functions
  • Direct VBUS and USB_ID input from the charging port
  • On-chip charger type detection
  • SPMI communication with the CPU
  • Works alongside the PM8937 main PMIC

Specifications

BrandQualcomm
ModelPMI8937
CategoryPower Management IC (Interface / Charging PMIC)
CompatibilityMSM8937 (Snapdragon 430) platform, companion to PM8937
TechnologySPMI bus interface; charger, fuel gauge, LED and PWM functions

Common Repair Uses

  • Phone not charging, no charging icon on charger insertion
  • Charger detected but battery percentage not rising
  • Dead phone after a faulty charger or voltage spike at the port
  • VBUS line short traced to the PMI8937
  • Liquid damage in the charging section
  • Battery percentage jumping or freezing (fuel gauge fault)
  • Re-doing a failed previous IC rework
  • Full charging-section rebuild on MSM8937 boards

Compatible Devices

  • Verified at chipset-platform level — confirm the PMI8937 marking on the board before replacement.
  • Qualcomm MSM8937 (Snapdragon 430) motherboards
  • Boards using the PM8937 + PMI8937 PMIC pair
  • Android smartphones built on Snapdragon 430 with PMI8937 fitted
  • Service boards and donor boards from the MSM8937 platform

FAQ

What is the product name?
The product name is Qualcomm PMI8937 Power IC.
What is the brand of this product?
The brand of this product is Qualcomm.
What is the model of this product?
The model of this product is PMI8937.
What is this product used for?
This product is used for replacing a faulty charging and interface PMIC on MSM8937 (Snapdragon 430) motherboards.
Which devices are compatible with this product?
This product is compatible with MSM8937 (Snapdragon 430) boards that use the PM8937 and PMI8937 PMIC pair.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is the PMI8937 the charging IC or the main power IC?
The PMI8937 is the charging and interface PMIC. It runs the charger, fuel gauge, LED and PWM functions, while the PM8937 supplies the main power rails on MSM8937 boards.
Can I use a PMI8952 in place of a PMI8937?
No. The PMI8952 is a different Qualcomm interface PMIC for other platforms, so always match the part number printed on the original chip before you replace it.