VC7916-62 Power IC Vanchip RF Power Amplifier Module
₨ 300
VC7916-62 Power IC for Mobile Network Section Repair
The VC7916-62 Power IC is a Vanchip RF power amplifier module that drives the transmit side of a smartphone’s cellular network section. When this PA fails, the phone typically shows no service, drops calls the moment it transmits, or pulls abnormal current on the battery line. You get a direct replacement part for boards that carry the original VC7916-62 marking, ready for hot air rework on your repair bench. Match the full marking, including the -62 suffix, before replacement so the module fits the footprint and works with the board’s RF calibration.
VC7916-62 Power Amplifier IC: Restoring the Transmit Path on Mobile Boards
The VC7916-62 power amplifier IC sits at the final stage of a smartphone’s RF transmit chain. The transceiver generates a low-power signal, and this Vanchip module boosts it to the level the antenna needs to reach the tower. Vanchip, a Tianjin-based RF front-end manufacturer, builds power amplifier and RF switch ICs for handsets across 2G to 5G platforms, and Chinese phone makers place its PA modules on a wide range of models. For a technician, the VC7916-62 Power IC matters because the PA draws heavy current directly from the battery rail and runs hot during every call and data session. That combination makes it one of the most common failure points in the network section of a dead phone or a phone with a persistent network issue.
How a Failed PA Shows Up on the Bench
PA faults tend to produce a recognizable pattern. The phone powers on, the IMEI reads correctly, and the baseband looks healthy, yet the handset shows no service or holds signal bars only until it tries to transmit. Outgoing calls drop within seconds, and mobile data fails to connect. In more severe cases, the PA develops an internal short on its supply pin, and the phone refuses to boot or drains the battery while switched off. A DC power supply reveals this quickly: you see high standby current, and the PA area heats up within seconds of connecting power. Water damage, a fall that cracks the module’s solder joints, and repeated high-power transmission in weak-signal areas all push this component toward failure. Because the PA connects directly to the VBAT rail, a shorted unit can drag down the entire board, so it belongs on your checklist whenever you trace a short back toward the RF section.
Diagnosing the VC7916-62 Before Replacement
Start with the board’s schematic or boardview to locate the PA and its supply, enable, and control lines. Measure the VBAT or VCC pin to ground in diode mode and compare the reading against a known-good board of the same model. If the line reads near zero, lift the shield and inject a controlled voltage from your power supply, then use rosin smoke, freeze spray, or a thermal camera to confirm the PA as the heat source. Check the surrounding filters, switches, and coupling capacitors as well, since a damaged filter can mimic a PA fault. Confirm that the transceiver delivers drive signal and that the control lines carry the expected logic levels before you commit to a component change. This step-by-step approach saves you from replacing a healthy Vanchip PA IC when the real fault lies elsewhere in the transmit path.
Replacing the Module Cleanly
Remove the RF shield carefully to protect the frame and nearby components. Apply quality flux around the module, preheat the board from below, and use hot air with even, circular movement until the solder reflows across all pads. Lift the old module straight up so the pads stay intact. Clean the footprint with solder wick and flux, level the pads, and inspect them under a microscope for lifted or bridged points. Tin the new VC7916-62 lightly or use stencil-based reballing, align it to the footprint markings, and reflow it into place while letting surface tension center the part. Once the board cools, recheck the supply line for shorts, power the phone on a DC supply, and watch the current draw while you place a test call. Stable current during transmit and a solid network registration confirm a successful repair.
The VC7916-62 Power IC fits naturally into a complete network repair workflow alongside a hot air station, a soldering station, a stereo microscope, and a PCB holder. For technicians who handle network faults daily, a DC power supply with a precise current display and a thermal camera form the logical upgrade path, cutting diagnosis time on shorted PA lines from minutes to seconds.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Original Vanchip VC7916-62 marking for direct footprint replacement
- ✓Final-stage RF amplification for the cellular transmit path
- ✓Restores network registration, calling, and mobile data after PA failure
- ✓Clears VBAT-line shorts caused by an internally failed PA
- ✓Suits hot air rework and stencil reballing workflows
- ✓Ideal for board-level network section repair in service centers
- ✓Useful for both water-damage and drop-damage RF repairs
- ✓Exact suffix matching protects the board’s RF calibration
Specifications
| Brand | Vanchip |
|---|---|
| Model | VC7916-62 |
| Category | Mobile Phone IC / RF Power Amplifier IC |
| Technology | RF power amplifier module for cellular transmit |
Common Repair Uses
- ✓No service or no network with a valid IMEI and working baseband
- ✓Calls dropping as soon as the phone transmits
- ✓Mobile data failing to connect while signal bars show
- ✓Shorted VBAT line traced to the PA module
- ✓High standby current or battery drain caused by a leaking PA
- ✓Dead phone that will not boot due to a PA short on the main supply
- ✓Network faults after water damage in the RF section
- ✓Cracked PA solder joints after a drop
Compatible Devices
- ✓Verified scope is marking-level — this part replaces modules carrying the VC7916-62 marking; no public device list exists for this suffix.
- ✓Smartphone boards fitted with the original VC7916-62 marking
- ✓Boards that list VC7916-62 in the manufacturer schematic or boardview
- ✓Donor-board swaps where both boards carry the identical -62 suffix
- ✓Handsets from Chinese manufacturers that use Vanchip PA modules on the same footprint (confirm marking first)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How do I check if the VC7916-62 PA IC is shorted?
Can I replace VC7916-62 with another VC7916 variant like VC7916-31 or VC7916-63?
Related products
339S00108 WiFi IC For iPad Air iPad Pro 9.7 Replacement
In stock
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock



