Vanchip VC7916-65 PA IC – RF Power Amplifier Module
₨ 400
Vanchip VC7916-65 PA IC for Network Fault Repair
The VC7916-65 PA IC is a Vanchip RF power amplifier module. It drives the transmit signal in the RF section of a smartphone. Technicians replace it when a phone shows no service or emergency calls only, or loses signal the moment a call connects. They also replace it when a shorted PA pulls down the battery line and the phone goes dead or heats up near the RF area. Mechanicpk supplies the exact -65 suffix, so your replacement matches the board marking. Pair it with a hot air station, a preheater, and a microscope for clean removal and placement on your repair bench.
VC7916-65 PA IC for Mobile RF Section Repair
The VC7916-65 PA IC is a radio frequency power amplifier module from Vanchip (Tianjin) Technology, a semiconductor company that builds RF front-end parts for smartphones, tablets, and wireless devices. Inside the handset, this module strengthens the transmit signal coming from the transceiver before it reaches the antenna path. That boost lets the phone register on the network and hold a call. A failed PA gives you a hardware fault that looks like a network issue: no service, emergency calls only, or a signal that collapses as soon as you dial. Mechanicpk stocks this exact-suffix part for technicians who trace these faults at board level and need a replacement that matches the original marking.
Where the VC7916-65 PA IC Sits in the RF Chain
A smartphone transmit path runs from the transceiver, through the power amplifier, into the switching and filtering stage, and out to the antenna. A PA module packs the amplifier stages and their control circuitry into one component, and it takes its supply from the battery rail through the board’s power circuitry. That position creates two typical fault patterns. In the first, an amplifier stage fails: the phone powers on normally, but it cannot transmit, so it shows no service or drops calls. In the second, the module shorts internally. That short drags down the battery line, heats the RF area, or leaves you with a dead phone that pulls heavy current on a DC power supply. Knowing which pattern you face tells you how to approach the board.
Diagnosing a Faulty Mobile PA IC Before Replacement
Rule out the simple causes before you change the IC. Open the phone’s status screen and confirm that the IMEI and baseband version read correctly, because a corrupted IMEI or baseband points to a software job, not a hardware one. Inspect the antenna connector, the coaxial cable, and the antenna contacts, since a loose or corroded connection mimics a dead PA. For short-circuit cases, power the board from a DC power supply and watch the current draw. Then locate the hot component with freeze spray, rosin vapor, or a thermal camera. Compare diode-mode readings on the PA supply line against a known-good board. Check closely for liquid corrosion around the module and its shield, because water damage often attacks the RF section first. Move to IC change karna only once these checks isolate the PA.
Replacement Workflow and Soldering Notes for Vanchip VC7916 Power Amplifier Modules
Read the full marking on the original part before ordering. Vanchip sells several VC7916 variants with different suffixes, so fit VC7916-65 only where the board originally carries VC7916-65. Mount the board in a PCB holder and bring it up to temperature with a preheater. Shield nearby plastic connectors and small components with Kapton tape. Apply flux, then heat the module evenly with a hot air station and a suitable nozzle, and lift it with tweezers only once the solder fully melts. Forcing it early tears pads off the board.
Clean the pads with solder wick and fresh flux. Then inspect them under a microscope for lifted or bridged pads before you continue. Align the new VC7916-65 PA IC by its orientation mark, reflow it with steady heat, and let the board cool naturally. Clean off flux residue, and confirm with a multimeter that the supply line no longer reads short. Insert a SIM, check network registration, make a test call, and monitor current draw and module temperature for a few minutes.
If your bench handles regular RF section work, a dedicated preheater and a higher-magnification microscope make PA swaps faster and much safer for the surrounding components.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Vanchip RF power amplifier module for smartphone transmit paths
- ✓Exact VC7916-65 suffix for marking-matched replacement
- ✓Restores network registration and call transmission once fitted correctly
- ✓Resolves PA-related short circuits on the battery supply line
- ✓Suits board-level RF section repair with hot air rework
- ✓Integrates amplifier stages and control circuitry in one module
- ✓Supports donor-free repair when a salvaged PA is not available
- ✓Designed for technicians who diagnose network faults at IC level
Specifications
| Brand | Vanchip (Tianjin) Technology |
|---|---|
| Model | VC7916-65 |
| Category | Mobile Phone ICs > RF Power Amplifier (PA) IC |
| Compatibility | Direct replacement on boards that originally carry VC7916-65 (match the full suffix) |
| Supported Devices | Smartphones whose RF section uses the VC7916-65 module |
| Technology | RF power amplifier module (PAM) for mobile handsets |
Common Repair Uses
- ✓No service or “emergency calls only” caused by a failed PA stage
- ✓Signal dropping the moment a call connects
- ✓Network issue after liquid damage in the RF section
- ✓Dead phone caused by a shorted PA pulling down the battery line
- ✓Phone heating near the RF area during standby or calls
- ✓High current draw on a DC power supply traced to the PA
- ✓PA replacement after a drop or impact damages the RF section
- ✓Replacing a burnt PA after a battery-line short or wrong charger damage
Compatible Devices
- ✓Universal at part level; not device-specific. The part fits any board designed for the VC7916-65.
- ✓Smartphone mainboards marked VC7916-65 in the RF/PA section
- ✓Boards whose schematic or parts list specifies VC7916-65
- ✓Donor-to-target swaps where both boards carry the identical -65 suffix
- ✓Android handsets built with Vanchip RF power amplifier modules (confirm the marking first)
- ✓Tablets and cellular devices whose RF board uses the VC7916-65
- ✓Refurbishment of RF boards that originally shipped with VC7916-65



