VC7916-55 Power IC | RF Power Amplifier PA Chip

₨ 300

Vanchip VC7916-55 Power Amplifier IC

The VC7916-55 Power IC is a Vanchip RF power amplifier (PA) chip that boosts your phone’s 4G transmit signal before it reaches the antenna. Technicians replace it when a board shows no service, a signal that drops during calls, or a battery-line short that traces back to the PA area. Replacement PA kits for the Xiaomi Redmi 9 and Redmi Note 9 list the VC7916, so this part suits network-section repair on those boards. Match the exact -55 suffix on the original chip before you fit it. The chip needs no programming, so a clean hot air swap and a call test complete the job.

14 People watching this product now!
Description

VC7916-55 PA IC for 4G Network Section Repair

The VC7916-55 PA IC is a radio-frequency power amplifier from Vanchip, a Tianjin-based RF front-end designer whose end customers include Xiaomi, OPPO and vivo. Inside the phone, this chip takes the low-level transmit signal from the transceiver and raises it to the power the antenna needs to reach the tower. Many Pakistani shops list it as the VC7916-55 Power IC, but it belongs to the network section, not the power management section. It controls how strongly the phone transmits; it does not generate the board’s supply rails. When the chip fails, you typically see no service, a signal that collapses during calls, or a short on the battery line that leads back to the PA area. Mechanicpk supplies it as a board-level replacement part for technicians who handle network faults on Xiaomi boards every week.

Where the VC7916-55 Sits in the RF Front-End

The transceiver generates the outgoing signal at a very low level, and the VC7916-55 PA IC amplifies it before the signal travels through the switch and filter stage to the antenna. Vanchip builds its 4G power amplifier modules for exactly this job and ranks among China’s largest 4G PA suppliers by shipment volume. The chip draws its supply straight from the battery rail, which explains why a failed PA can pull the whole VBAT line down and leave you with a phone that looks completely dead. Replacement PA kits for the Redmi 9 and Redmi Note 9 list the VC7916 alongside the VC7643 and QPM5541, so expect to find it among the other RF parts under the network shield. Vanchip produces several VC7916 suffixes, including -36 and -55, and you must match the exact marking on the original chip. Check that marking under magnification before you order any Redmi Note 9 PA IC.

Diagnosing a Faulty PA Before You Replace It

Confirm the fault before you lift the chip. Start with the basic checks: SIM tray, IMEI status, baseband version and antenna contacts. If the phone shows a valid IMEI and baseband but still reports no service, or the signal bars fall the moment you place a call, the transmit path becomes your main suspect. Connect the board to a DC power supply and watch the current draw; a battery-line short with heat building around the PA area points straight at a damaged amplifier. Use a multimeter in diode mode to compare the PA supply pads against a known-good board. Freeze spray or a thermal camera helps you locate the hot spot quickly on a shorted VBAT line. Replace the VC7916-55 only after these readings confirm the fault, because a weak signal can also come from a damaged transceiver, a broken antenna flex or corrupted calibration data.

Replacement Workflow on Your Repair Bench

Mount the board firmly in a PCB holder and remove the network shield carefully so you do not disturb nearby passives. Apply a quality no-clean flux around the chip and heat it with a hot air station at moderate airflow, keeping the nozzle moving so the small capacitors beside the PA stay in place. Lift the old chip once the solder flows, then clean the pads with desoldering wick and your soldering station until every pad sits flat and bright. Inspect the area under a microscope for torn or bridged pads before you continue. Tin the pads lightly, align the new chip by its pin-1 marking, and reflow it until it settles onto the pads by itself. After the board cools, check the battery line for shorts, power the phone, and test calls and mobile data on both SIM slots. The chip carries no firmware, so you need no box or flashing after the swap. Shops that handle multi-chip RF work daily can step up to a rework station with a built-in preheater, which reduces board stress during shield and PA removal.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Vanchip RF power amplifier for the 4G cellular transmit path
  • Exact -55 suffix for direct replacement of the original marking
  • Draws supply directly from the battery rail, making it a key suspect in VBAT shorts
  • No firmware, no programming and no box needed after replacement
  • Suits network section repair on Redmi 9 and Redmi Note 9 boards
  • Works with standard hot air rework, flux and pad preparation
  • Restores transmit power for stable calls and mobile data
  • Board-level part for professional repair benches and service centers

Specifications

BrandVanchip
ModelVC7916-55
CategoryMobile ICs > RF / Network ICs
CompatibilityBoards listed with VC7916 PA, including Xiaomi Redmi 9 and Redmi Note 9 (match the -55 suffix)
TechnologyRF power amplifier (PA) for the 4G cellular transmit path

Common Repair Uses

  • No service or “emergency calls only” with a valid IMEI and baseband
  • Signal dropping the moment a call connects
  • Weak network signal in a strong-coverage area
  • Battery line (VBAT) short traced to the PA area
  • Dead phone drawing high current on a DC power supply due to a shorted PA
  • Heating near the network shield during calls or mobile data use
  • Network section repair after water damage
  • Replacing a PA damaged during earlier board rework

Compatible Devices

  • Verified scope covers boards that use the VC7916 PA with the -55 suffix; always match the original chip marking.
  • Xiaomi Redmi 9 (VC7916 listed in its replacement PA set)
  • Xiaomi Redmi Note 9 (VC7916 listed in its replacement PA set)
  • Any handset board where the original PA carries the VC7916-55 marking
  • VC7916-series positions only where the -55 suffix matches

FAQ

What is the product name?
The product name is VC7916-55 Power IC.
What is the brand of this product?
The brand of this product is Vanchip.
What is the model of this product?
The model of this product is VC7916-55.
What is this product used for?
This product is used for replacing a faulty RF power amplifier in the network section of a mobile phone board to fix no service, weak signal and PA-related battery-line shorts.
Which devices are compatible with this product?
This product is compatible with boards that use the VC7916 PA with the -55 suffix, including Xiaomi Redmi 9 and Redmi Note 9 boards; always match the marking on the original chip.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can a shorted VC7916-55 PA IC cause a dead phone?
Yes. The PA takes its supply directly from the battery line, so an internal short can pull VBAT down and stop the phone from powering on. Check the current draw on a DC power supply and look for heat at the PA before you replace it.
Does the VC7916-55 need programming or flashing after replacement?
No. The chip carries no firmware, so you do not need a box or software after the swap. If the signal stays weak after replacement, check the antenna path, the transceiver and the device’s calibration data.