YCS 3S UV Curing Beige Mask | UV Solder Mask
₨ 500
UV Curing Solder Mask for Phone Boards
The YCS 3S UV Curing Beige Mask is a UV curing solder mask that hardens in about 3 seconds under UV light. You apply it over jumper wires, charging tail plug pads, screw posts and exposed copper after soldering, cure it with your UV lamp, and move straight to the next test. It works at board level, so it suits dead phone, charging issue and hardware fault repairs across brands instead of one device model. Mechanicpk supplies the beige 3S version for technicians who need fast, repeatable insulation and wire support on the repair bench.
In stock
YCS 3S UV Curing Beige Mask: UV Curing Solder Mask for Board-Level Repair
The YCS 3S UV Curing Beige Mask is a single-component UV curing solder mask built for board-level mobile phone repair. Under UV light it hardens in about 3 seconds, so you stop waiting on slow air-dry coatings and keep your repair bench moving. You use it wherever bare copper, a fresh jumper wire or a lifted pad needs insulation and mechanical support. This page explains where the mask fits in your workflow, which technical properties matter, and how to apply it so the cure holds on a working board.
Where This UV Curing Solder Mask Fits Your Repair Workflow
Most dead phone and charging issue jobs end with a hardware fix that leaves something exposed: a jumper wire running across a damaged trace, a charging tail plug pad you rebuilt, or a screw post pad that lifted during rework. The YCS 3S mask locks those repairs in place. You flow it over the joint, cure it with UV light, and the wire stays where you put it. The same mask insulates solder joints after welding and restores areas where the factory solder mask layer peeled or suffered partial damage. It also fixes enamelled wire runs and protects nearby components from accidental shorts when you close the phone. Whether you finish a reflow job on a hot air station or touch up a pad with your soldering station, the mask closes the job in seconds instead of minutes. High-volume technicians benefit most, because the fast cure removes the idle time between placing a wire and running the next test.
Technical Highlights of the 3S Cure and Beige Formulation
The defining spec is cure speed. The mask reaches a hard cure in roughly 3 seconds under UV light, which the product name abbreviates as 3S. Supplier information lists high temperature resistance with no softening once cured, plus oil resistance and no whitening, so the cured coating holds its shape on a board that sees heat. Because it ships as a single-component material, you skip mixing and pot-life tracking. You pick up what you need and apply it. YCS sells the same 3S formula in transparent, beige and green versions, and this listing covers the beige one. Many technicians search for this type of coating as UV green oil for mobile repair, whatever the actual shade. The mask ships as the coating only, so you need your own UV curing lamp on the bench.
Application Steps for a Reliable Cure
Clean flux residue from the area with isopropyl alcohol and let it dry before you apply the mask. Secure the board in a PCB holder and work under a microscope, so you place a thin, controlled bead over the joint instead of flooding nearby pads. Hold your UV lamp close and expose the mask directly. UV light only cures what it reaches, so keep layers thin and avoid burying the mask beneath components where your lamp cannot shine. After the cure, press a probe tip against the edge to confirm the surface has hardened, then check continuity with your multimeter before you reassemble the phone. A jumper wire UV solder mask coating protects the wire only when the joint underneath is sound, so test the connection first and mask second.
Keep the cap closed and store the bottle away from direct light between jobs, because UV-curable materials react to light. Pair the mask with your reballing kit and hot air station for CPU and BGA jobs. Keep it beside your ISP pinout tools and test box too, since the thin jumper wires on flashing and eMMC or UFS repairs need support that survives handling. Store the beige 3S mask in the same drawer as your flux, solder wire and tweezers, so it sits within reach the moment a jumper wire goes in.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Cures in approximately 3 seconds under UV light
- ✓Single-component material, no mixing required
- ✓Fixes jumper wires, tail plugs, screw posts and pads
- ✓High temperature resistance, no softening after cure
- ✓Oil resistance with no whitening
- ✓Insulates and protects components after welding
- ✓Repairs peeled or partially damaged PCB solder mask
- ✓Beige shade from the YCS 3S range (also sold in transparent and green)
Specifications
| Brand | YCS |
|---|---|
| Model | YCS 3S Beige |
| Category | UV Solder Mask (UV Curing Green Oil) |
| Compatibility | Universal — board-level use, not device-specific |
| Supported Devices | Mobile phone motherboards and PCBs of any brand |
| Technology | UV light curing, approximately 3-second cure |
Common Repair Uses
- ✓Verified board-level repair scenarios for UV solder mask
- ✓Fixing and insulating jumper wires on damaged traces
- ✓Securing charging tail plug pads after rebuild
- ✓Repairing screw post pads that lifted during rework
- ✓Keeping jumper wire coil pads from lifting off
- ✓Insulating and protecting components after welding
- ✓Restoring peeled or partially damaged PCB solder mask
- ✓Fixing enamelled wire on the board
- ✓Fixing and protecting solder joints, pads and chips in place
Compatible Devices
- ✓Universal — not device-specific; works at board level on mobile phone motherboards and PCBs regardless of brand
- ✓Mobile phone motherboards (any brand)
- ✓Charging tail plug connector pads
- ✓Screw post (standoff) pads
- ✓Jumper wire (flying wire) points
- ✓Enamelled wire repair runs
- ✓Lifted or damaged solder pads
- ✓Areas of peeled or partially damaged PCB solder mask
- ✓Solder joints needing post-weld insulation
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How long does the YCS 3S UV curing solder mask take to cure, and do I need a UV lamp?
Can I use this mask to hold a jumper wire in place on a dead phone board?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



