Qualcomm PM8150A 102 Power IC for Snapdragon 865 Boards
₨ 250
Qualcomm PM8150A 102 Power Management IC
The Qualcomm PM8150A 102 is a power management IC for the Snapdragon 865 (SM8250) platform. On the board it runs alongside the PM8250 core PMIC and the PM8150B charger PMIC. Teardown analysis confirms it on the Xiaomi Mi 10 mainboard. Technicians replace this chip on dead phones, boards that draw abnormal current, and sets that cut off during power-up because of a failed supply rail. Match the 102 marking on the original chip before you order. Pair it with a reballing stencil, quality flux, and a controlled hot air station for a clean IC change on flagship-class Qualcomm boards.
PM8150A Power IC for Qualcomm Snapdragon 865 Boards
The PM8150A power IC is a Qualcomm power management chip built for the Snapdragon 865 (SM8250) platform. Qualcomm documents it under one device specification with the PM8150L. On an SM8250 board it works next to the PM8250, which handles core power, and the PM8150B, which manages charging and the fuel gauge. This listing covers the chip with the 102 marking code. TechInsights identified the PM8150A on the Xiaomi Mi 10 mainboard, the first commercial Snapdragon 865 phone. That tells you where this chip reaches your bench: flagship boards with a multi-PMIC power tree. When the PM8150A fails, the phone usually arrives as a dead phone or as a board that pulls abnormal current from your DC supply the moment you press power.
Where the PM8150A Sits in a Snapdragon 865 PMIC Layout
Snapdragon 865 boards split power duties across several PMICs, and each chip owns its own group of regulated rails. All of them start together in a controlled power-up sequence. A fault in one PMIC can stall the whole sequence, so a single failed chip produces symptoms that look like a CPU or memory fault: no boot, no logo, or a board that shuts down after a second of current. This split saves you diagnostic time. If the charging section responds and the battery reads correctly but the phone stays dead, the PM8150A and PM8250 move up your suspect list. Boards such as the Mi 10 also carry a PM8009 camera PMIC and a PMX55 for the 5G modem, so map every power chip on the board before you lift anything.
Diagnosing a Faulty PM8150A Power IC Before IC Change
Confirm the fault before you touch hot air. Connect the board to a DC power supply and watch the current reading when you press power. A short on an output rail shows up as instant high current. Take diode-mode readings with your multimeter on the capacitors around the chip to find the rail that has collapsed. Freeze spray, rosin smoke, or a thermal camera then shows you whether the heat comes from the IC body or from a shorted capacitor beside it. A shorted capacitor costs you far less than an IC change karna, so rule it out first. If the heat sits on the PM8150A itself, or the chip produces no output rails while its input supply reads correct, you have a genuine PMIC fault. Liquid-damaged boards need extra care. Corrosion under the chip can mimic a dead PMIC, so clean the area and recheck before you order a replacement.
Replacement Workflow on Your Repair Bench
PM8150A replacement is board-level work, and preparation decides the result. Mount the board in a PCB holder, protect nearby components with heat-resistant tape, and preheat the board evenly. Lift the old chip with a hot air station and quality flux, then clean the pads with solder wick. Inspect every pad under a microscope for lifts or tears before you go further, because one damaged pad turns a simple swap into a jumper lagana job. Reball the new PM8150A 102 IC with the correct stencil from your reballing kit, align it to the board outline, and reflow it with steady, even heat. Check each output rail in diode mode before first power, then confirm normal current draw on the DC supply. Always match the marking on the original chip before ordering. PM8150A, PM8150L, PM8150B, and PM8150C handle different jobs, and the wrong variant will not revive a dead board. If you handle Snapdragon 865 boards often, a stereo microscope is the upgrade that pays back fastest on fine-pitch PMIC work.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Qualcomm power management IC for the Snapdragon 865 (SM8250) platform
- ✓Carries the 102 marking code for exact-match replacement
- ✓Shares Qualcomm’s device specification with the PM8150L
- ✓Works alongside the PM8250 core PMIC and PM8150B charger/fuel gauge PMIC
- ✓Teardown-confirmed on the Xiaomi Mi 10 mainboard
- ✓Supplies its own group of regulated rails within a multi-PMIC power tree
- ✓Replacement part for IC-level and PCB-level repair
- ✓Suited to hot air, reballing, and microscope-based rework workflows
Specifications
| Brand | Qualcomm |
|---|---|
| Model | PM8150A (marking 102) |
| Category | Power Management IC (PMIC) |
| Compatibility | Qualcomm Snapdragon 865 (SM8250) platform |
| Supported Devices | Xiaomi Mi 10 (teardown-confirmed) |
| Technology | Multi-PMIC power tree companion IC (documented with PM8150L) |
Common Repair Uses
- ✓Dead phone with no power-up on Snapdragon 865 boards
- ✓High current draw on the DC supply from a shorted PMIC rail
- ✓Board that powers on, then cuts off within a second (power sequence failure)
- ✓No boot or hang on logo traced to a missing PM8150A supply rail
- ✓Replacing a PM8150A that heats up under rosin or a thermal camera
- ✓PMIC replacement after liquid damage and corrosion
- ✓Reflow or reball of a PMIC with cracked joints after drop damage
- ✓Board-level IC change in service center and training-institute workflows
Compatible Devices
- ✓Verified at chipset-platform level, with one teardown-confirmed phone model
- ✓Qualcomm Snapdragon 865 (SM8250) boards that carry the PM8150A
- ✓Xiaomi Mi 10 (PM8150A confirmed on mainboard)
- ✓Qualcomm QRB5165 platform boards (PM8150A listed in Qualcomm’s QRB5165 PMIC documentation)
- ✓Any board whose original chip carries the PM8150A 102 marking
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can PM8150B replace PM8150A on a Snapdragon 865 board?
How do I check if the PM8150A is shorted on a dead Snapdragon 865 phone?
Related products
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock



