PM8009 001-00 Power IC – Snapdragon 865 Camera PMIC
₨ 300
PM8009 001-00 Power IC for Snapdragon 865 Camera Circuits
The PM8009 001-00 Power IC is the Qualcomm PM8009 camera PMIC. Qualcomm designed it to power the camera module on the Kona chipset, the Snapdragon 865 platform. It works alongside the main PMIC set on these boards and supplies power to the camera subsystem alone. When a Snapdragon 865 phone boots, charges and displays normally but the camera refuses to open, this chip deserves close inspection. Mechanicpk supplies the PM8009 for board-level technicians who need the exact 001-00 marking for a clean, like-for-like IC replacement on flagship Qualcomm motherboards.
PM8009 001-00 Power IC: Dedicated Camera Power Management for Snapdragon 865 Boards
The PM8009 001-00 Power IC is the Qualcomm PM8009 camera PMIC, a dedicated power management chip that Qualcomm built to support the camera module on its Kona chipset, the Snapdragon 865 platform. On these motherboards, the main PMIC set handles core rails, display power and charging, while the PM8009 takes a narrower job: feeding the camera subsystem. That division shapes your diagnosis. A phone that boots cleanly, charges normally and shows a perfect display, yet fails to open its camera, points you away from the main PMIC and toward this chip.
Where the PM8009 Camera PMIC Sits on a Snapdragon 865 Board
Qualcomm’s Snapdragon 865 reference schematics list the PM8009 next to the PM8250, PM8150L and PM8150B as part of the platform’s full PMIC lineup. Teardown analysis of the Xiaomi Mi 10, the first commercial Snapdragon 865 phone, confirms the PM8009 on its main board alongside the PM8150A. This placement tells you two things. The PM8009 belongs to flagship-class Qualcomm designs, not MediaTek or Unisoc boards. It also serves a single subsystem, so a failed unit produces a focused symptom set rather than a dead phone.
Symptoms That Point to a PM8009 Fault
A camera power fault usually shows up as a camera app that crashes on launch, a black viewfinder, or a “camera failed” message. When every camera on the phone stops working at once while the rest of the board runs normally, a shared supply problem becomes more likely than a single bad sensor. Intermittent camera operation after a drop or liquid damage fits the same pattern. Treat these signs as leads, not verdicts. Rule out software corruption and a faulty camera flex first, because both produce identical complaints at the counter.
Verifying the IC Before You Replace It
Start with the cheapest test: fit a known-good camera module and check whether the fault follows the module or stays with the board. If it stays, take diode-mode readings on the camera supply lines with a multimeter and compare them against a healthy board of the same model. A reading near zero signals a short on the line. Inject a low, current-limited voltage from a DC power supply and watch which component warms up, using rosin smoke or a thermal camera. If the PM8009 receives its input supply but delivers nothing on its outputs, you have a strong case for an IC change.
Rework Setup for a Wafer-Level Package
Qualcomm’s ordering code for this part, PM-8009-1-WLNSP49D, identifies a wafer-level package. These chips carry a thin, exposed die and very fine solder balls, so they reward a controlled rework process. Use a hot air station with stable, low airflow, a good no-clean flux and a preheated board in a PCB holder. Never lever the old chip off the pads; lift it only once the solder fully melts. Clean the pads with a soldering station and fine wick, then inspect them under a microscope for lifted or bridged pads before you place the new part. Check the ball surface of the replacement under magnification as well, and reball with a matching stencil from a reballing kit if any ball looks uneven.
Matching the Marking: Why 001-00 Matters
The 001-00 suffix identifies this exact part version. Compare it against the marking on the original chip before you order. Do not swap in another Qualcomm camera PMIC such as the PM8008 or PM8010. Qualcomm lists the PM8008 in a 20-pin wafer-level package, so its footprint has nothing in common with the PM8009’s ball layout, and the PM8010 serves later platforms with its own configuration.
Who Needs This Part
This IC suits board-level technicians, service centers and repair shops that handle flagship Snapdragon 865 phones and prefer a chip-level repair over replacing a full motherboard. For a camera fault isolated to a power rail, a correct PM8009 swap restores the camera at a fraction of the cost of a board. Pair it with the right test equipment and a disciplined rework routine, and you turn a hardware fault that other shops reject into a billable job.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Qualcomm camera PMIC built specifically for the Snapdragon 865 (Kona) camera module
- ✓Exact PM8009 001-00 marking for like-for-like replacement
- ✓Dedicated camera supply role makes fault isolation faster and cleaner
- ✓Teardown-confirmed fitment on the Xiaomi Mi 10 main board
- ✓Wafer-level package suited to controlled hot air rework
- ✓Restores camera function without replacing the motherboard or camera assembly
- ✓Fits into a standard board-level workflow: diagnose, remove, clean, reball, place
- ✓Supplied for professional technicians and service centers across Pakistan
Specifications
| Brand | Qualcomm |
|---|---|
| Model | PM8009 001-00 |
| Category | Power Management IC (Camera PMIC) |
| Compatibility | Qualcomm Snapdragon 865 (Kona) platform |
| Supported Devices | Xiaomi Mi 10 (teardown-confirmed) |
| Technology | Dedicated camera module power management, wafer-level (WLNSP) package |
Common Repair Uses
- ✓Camera app fails to open on a Snapdragon 865 board
- ✓All rear and front cameras dead at the same time
- ✓Black viewfinder with a working display and touch
- ✓Short on camera supply lines confirmed in diode mode
- ✓PMIC replacement after drop or liquid damage to the camera power area
- ✓Burnt or cracked camera PMIC found during board inspection
- ✓Donor board IC swap where a new chip offers better reliability
- ✓Camera power restoration as an alternative to motherboard replacement
Compatible Devices
- ✓Verified at chipset-platform level, with one teardown-confirmed handset
- ✓Qualcomm Snapdragon 865 (SM8250 / Kona) motherboards
- ✓Xiaomi Mi 10 (main board, confirmed by teardown analysis)
- ✓Boards that pair PM8250, PM8150L and PM8150B with a separate camera PMIC
- ✓Any board carrying an original chip marked PM8009 001-00
- ✓Not for MediaTek, Unisoc or Exynos motherboards
- ✓Not interchangeable with PM8008 or PM8010 camera PMICs



