77645-21 IC – Skyworks SKY77645-21 PA IC 3G/4G

₨ 200

Skyworks 77645-21 IC – 3G/4G Multiband PA Module

The 77645-21 IC is the Skyworks SKY77645-21 SkyLiTE multimode multiband power amplifier module, the chip that drives uplink transmission in 3G and LTE smartphone boards. It covers CDMA, WCDMA, TD-SCDMA, FDD LTE, and TDD LTE bands inside a compact 42-pad MCM package measuring 4.0 × 6.8 × 0.75 mm. The modem controls it over MIPI, and a DC-DC converter supplies it through average power tracking. When this PA fails, you see no service, dropped calls, dead mobile data, or a supply-line short that leaves you with a dead phone. Replace it with the exact -21 variant your board carries.

16 People watching this product now!
Description

SKY77645-21 PA IC: Multimode Transmit Engine for 3G and LTE Boards

The 77645-21 IC is the Skyworks SKY77645-21 PA IC, a SkyLiTE multimode multiband (MMMB) power amplifier module that boosts the RF transmit signal before it reaches the antenna path. Skyworks packs an InGaP amplifier die, a silicon CMOS control die, and passive components onto a multi-layer laminate substrate, then seals everything inside a 4.0 × 6.8 × 0.75 mm, 42-pad MCM surface-mount package. One module handles low, mid, and high bands across 3G and 4G, so a single failed PA can take down almost the entire uplink side of the phone. That explains the classic network issue complaints: full bars that vanish on a call attempt, mobile data that downloads but never uploads, or no service at all. Mechanicpk supplies this part for technicians who diagnose RF faults at chip level and need the exact part number on the bench.

Band Coverage and Internal Architecture

Skyworks rates this module across five air interfaces. CDMA support spans BC0, BC1, BC4, BC6, BC10, and BC15. WCDMA coverage includes Bands I, II, III, IV, V, VIII, and IX, and TD-SCDMA runs on Bands 34 and 39. On the LTE side, you get FDD Bands 1, 2, 3, 4, 5, 7, 8, 9, 12, 13, 17, 20, 25, 26, 28, and 30, plus TDD Bands 38, 39, 40, and 41. Inside the package, separate low-, mid-, and high-band WCDMA/LTE blocks sit beside a Multi-Function Control (MFC) block, two T/R ports, and ten RF outputs. Skyworks matches the RF input and output ports internally to 50 ohms, which cuts the external component count around the chip and leaves fewer passives for you to probe during diagnosis. For 4G traffic, the module handles channel bandwidths from 1.4 MHz up to 40 MHz and supports uplink carrier aggregation on Band 39 (up to 35 MHz) and Bands 40/41 (up to 40 MHz).

How the 77645-21 Power Amplifier Module Handles Power and Control

Skyworks optimized this 77645-21 power amplifier module for average power tracking (APT) with a DC-DC converter. The input drive level sets output power, while the converter adjusts VCC to the lowest level that still meets each power step, which keeps current draw and heat down. MIPI-programmable bias modes let the modem balance efficiency against linearity separately for 3G and 4G. Extremely low leakage current protects standby time when the radio sits idle. This architecture matters during fault-finding. A shorted PA often pulls its supply rail to ground and turns a network fault into a high-current or dead phone complaint, so isolate the DC-DC output from the PA before you condemn either part. The modem talks to the module over the MIPI RFFE lines (SCLK and SDATA), and a broken control line can mimic a dead PA. Measure those lines in diode mode with a multimeter and compare readings against a known-good board before you start a chip swap.

Replacement Workflow with a 4G PA IC for Mobile Repair

Replacing a 4G PA IC for mobile repair demands controlled heat and accurate pad alignment. Lock the board in a PCB holder, remove the RF shield, and protect nearby connectors and plastic parts with heat-resistant tape. Apply quality flux and lift the old module with a hot air station using steady, even airflow so you avoid lifting neighbouring filters and passives. Clean the 42 pads with desoldering wick, check them under a microscope for torn pads or bridged traces, then tin them lightly and evenly. Align the new SKY77645-21 PA IC by its pin-1 marker, reflow, and let the board cool naturally. Check the supply rail for shorts before power-on, then test calls and data on every band your network uses. Always match the full suffix: Skyworks also produces a SKY77645-11 variant, so read the marking on the original chip before ordering. For heavy board-level RF work, a preheater makes a sensible upgrade, since it reduces thermal stress on multi-layer boards during removal. You can source hot air stations, microscopes, PCB holders, and multimeters from the related Mechanicpk categories to complete this workflow.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Genuine Skyworks SkyLiTE MMMB power amplifier module
  • Covers CDMA, WCDMA, TD-SCDMA, FDD LTE, and TDD LTE in one package
  • Separate low-, mid-, and high-band WCDMA/LTE amplifier blocks
  • Two T/R (RX) ports and ten RF outputs
  • Fully programmable MIPI control with selectable bias modes
  • APT DC-DC optimized for high efficiency at every power level
  • Uplink carrier aggregation on Bands 39, 40, and 41
  • Compact 4.0 × 6.8 × 0.75 mm, 42-pad MCM footprint

Specifications

BrandSkyworks Solutions
ModelSKY77645-21 (SkyLiTE)
CategoryMultimode Multiband Power Amplifier Module (PA IC)
CompatibilityCDMA BC0/1/4/6/10/15; WCDMA I/II/III/IV/V/VIII/IX; TD-SCDMA 34/39; FDD LTE 1/2/3/4/5/7/8/9/12/13/17/20/25/26/28/30; TDD LTE 38/39/40/41
Supported DevicesMultiband 3G/LTE handsets that carry the SKY77645-21 module
TechnologyInGaP amplifier die with CMOS MIPI controller, APT DC-DC operation, 50-ohm matched RF ports
MaterialInGaP and silicon dies with passives on a multi-layer laminate substrate, encapsulated MCM
Dimensions4.0 × 6.8 × 0.75 mm, 42-pad MCM SMT package

Common Repair Uses

  • No service or “emergency calls only” caused by a failed PA
  • Calls that drop the moment they connect
  • Mobile data that receives but fails to upload
  • Dead phone or high current draw from a shorted PA supply rail
  • Weak LTE or 3G transmit on specific bands
  • Water-damaged RF section with a corroded or burnt PA
  • Drop damage with a cracked PA module or lifted pads
  • Board-to-board PA transplant during RF section rebuild

Compatible Devices

  • Universal across multiband 3G/LTE smartphone boards fitted with the SKY77645-21 module — confirm the marking on the original PA before replacement
  • Smartphone boards with an original SKY77645-21 / 77645-21 marked PA
  • CDMA handsets on BC0, BC1, BC4, BC6, BC10, BC15
  • WCDMA/HSPA+ handsets on Bands I, II, III, IV, V, VIII, IX
  • TD-SCDMA handsets on Bands 34 and 39
  • FDD LTE handsets on low bands 5, 8, 12, 13, 17, 20, 26, 28
  • FDD LTE handsets on mid/high bands 1, 2, 3, 4, 7, 9, 25, 30
  • TDD LTE handsets on Bands 38, 39, 40, 41
  • MIPI RFFE-controlled RF front-end designs with APT DC-DC supply

FAQ

What is the product name?
The product name is 77645-21 IC – Skyworks SKY77645-21 PA IC.
What is the brand of this product?
The brand of this product is Skyworks Solutions.
What is the model of this product?
The model of this product is SKY77645-21.
What is this product used for?
This product is used for replacing a faulty 3G/4G power amplifier module on smartphone boards that show no service, call drops, data upload failure, or a shorted PA supply rail.
Which devices are compatible with this product?
This product is compatible with multiband 3G/LTE smartphone boards that originally carry the SKY77645-21 module across CDMA, WCDMA, TD-SCDMA, FDD LTE, and TDD LTE bands.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does the SKY77645-21 PA IC handle 2G GSM calls?
No. Skyworks lists CDMA, WCDMA, TD-SCDMA, and LTE modes for this module and lists no GSM or EDGE mode, so a 2G-only transmit fault points to another part of the RF section.
Can I use SKY77645-11 in place of SKY77645-21?
Treat them as separate parts. Skyworks produces SKY77645-11 as its own variant, so match the full marking on the original module and fit the -21 only where the board carried a -21.