Qualcomm WTR3925 Network IC – 28nm RF Transceiver
₨ 200
Qualcomm WTR3925 Network IC for LTE-A Board Repair
The Qualcomm WTR3925 handles 2G, 3G and 4G LTE transmit and receive on its host board, and it works with the Gobi 9×35 modem family. Qualcomm built it on a 28nm RF process with single-chip carrier aggregation, so the board needs no companion transceiver. You find this network IC on iPhone 6s, LG G4, LG G5, Nexus 5X and HTC One M9 logic boards. Technicians fit it on boards with no service, a phone stuck on searching, or a confirmed transceiver hardware fault after a drop or liquid damage. Pair it with a matching reballing stencil and a controlled hot air profile for a clean, reliable fit.
WTR3925 Network IC: Qualcomm’s 28nm LTE-A RF Transceiver
The WTR3925 network IC is the RF transceiver in Qualcomm’s fourth-generation 3G/LTE multimode platform, and it sits between the baseband modem and the RF front end on every board that carries it. Qualcomm launched it with the Gobi 9×35 modem and RF360 front-end parts as the first RF transceiver on a 28nm process. The chip converts baseband signals to RF for transmission and brings received RF back down to baseband for the modem. When this IC develops a hardware fault, the phone shows no service, unstable signal, or a radio that never registers on the network, even with a healthy SIM path and antenna. For your repair bench, that makes WTR3925 a high-value replacement part across a focused group of flagship boards from the 2015–2016 generation.
Inside the Qualcomm WTR3925 RF Transceiver
Qualcomm designed the WTR3925 as its first single-chip carrier aggregation transceiver, covering every carrier aggregation band combination 3GPP had approved at launch. Earlier platforms paired a WTR1625L with a WFR1620 companion chip to aggregate carriers; WTR3925 drops that second chip and moves from a 65nm to a 28nm RF process. The chip supports GSM/EDGE, HSPA+, CDMA 1X EV-DO, TD-SCDMA and LTE in both FDD and TDD modes, so one part runs the full multimode radio. Its transmit side provides ten single-ended outputs across low-band and mid/high-band paths, while the receive side runs separate primary and diversity downconverters for each aggregated carrier. Qualcomm integrated its IZat location platform as well, with GPS, GLONASS and BeiDou support. That level of integration explains why one failed transceiver can take down every network band at once instead of a single band.
Where the WTR3925 Network IC Fits on Real Boards
Teardowns confirm this IC as the iPhone 6s network IC, where it works with the MDM9635M LTE Cat 6 modem. It also appears on Android flagships built around Snapdragon 808, 810 and 820 platforms, including the LG G4, LG G5, Nexus 5X and HTC One M9. On these boards, the transceiver links the modem to the power amplifier modules and front-end switches that feed the antennas. A failed chip or a cracked solder joint under it breaks that chain, so the phone loses its network while the rest of the board powers up normally. Before you commit to IC change karna, measure the transceiver supply rails and check the antenna feed, PA module and front-end switches with your multimeter and microscope. That diagnosis step separates a true transceiver hardware fault from a simpler antenna or connector problem. Confirm the WTR3925 marking on the original chip before you order, since iPhone 6 boards use a WTR1625L that serves a different modem generation.
Replacing the WTR3925: Rework Workflow for Your Bench
Treat WTR3925 replacement as standard BGA rework with a few RF-specific precautions. Secure the board in a PCB holder, mask nearby shields and small passives with heat tape, and preheat the board so your hot air station lifts the chip without lifting pads. On boards with underfill, soften and clear it gradually with fine tweezers instead of forcing the IC off. Clean the pads with flux and wick, reball the new chip with a matching stencil from your reballing kit, and seat it with a controlled profile and enough flux for the balls to self-align. After reassembly, confirm network registration, test calls and mobile data on more than one band, and check GPS lock, since the transceiver carries location functions on these platforms. If you handle frequent board-level network jobs, upgrading to a stereo microscope with a board preheater makes underfill removal and ball inspection far more predictable.
| Weight | 0.1 kg |
|---|
Key Features
- ✓First Qualcomm RF transceiver built on a 28nm process
- ✓Single-chip carrier aggregation with no companion transceiver required
- ✓Supported all 3GPP-approved carrier aggregation band combinations at launch
- ✓Multimode radio: GSM/EDGE, HSPA+, CDMA 1X EV-DO, TD-SCDMA and LTE
- ✓LTE FDD and TDD support with carrier aggregation
- ✓Ten single-ended transmit outputs across low-band and mid/high-band paths
- ✓Separate primary and diversity downconverters per aggregated carrier
- ✓Integrated IZat location platform with GPS, GLONASS and BeiDou support
Specifications
| Brand | Qualcomm |
|---|---|
| Model | WTR3925 |
| Category | Mobile Phone ICs > Network / RF Transceiver ICs |
| Compatibility | Qualcomm Gobi 9x35 (MDM9635M) modem platform; Snapdragon 808, 810 and 820 boards |
| Supported Devices | Apple iPhone 6s, LG G4, LG G5, Google Nexus 5X, HTC One M9 |
| Technology | 28nm RF CMOS process, LTE-Advanced carrier aggregation, 2G/3G/4G multimode, LTE FDD and TDD, integrated IZat location (GPS/GLONASS/BeiDou) |
Common Repair Uses
- ✓Board-level network repair on WTR3925-based logic boards
- ✓Network IC replacement on boards showing No Service or Searching
- ✓Re-seating a transceiver with cracked solder joints after a drop
- ✓Reballing and refitting after liquid damage corrodes the pads under the IC
- ✓Fixing weak or unstable signal across multiple bands after a confirmed transceiver fault
- ✓Restoring GPS lock when diagnosis traces the fault to the transceiver
- ✓Replacing a damaged IC after a failed earlier rework attempt
- ✓Pad repair and IC refit on boards with lifted transceiver pads
- ✓BGA RF IC rework practice in repair training institutes
Compatible Devices
- ✓Verified board-level fitment; confirm the WTR3925 marking on the original chip before ordering
- ✓Apple iPhone 6s
- ✓HTC One M9
- ✓LG G4
- ✓LG G5
- ✓Google Nexus 5X
- ✓Snapdragon 810 (MSM8994) platform boards
- ✓Snapdragon 808 (MSM8992) platform boards
- ✓Qualcomm Gobi 9x35 / MDM9635M modem platforms
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is WTR3925 a power IC or a network IC?
Can WTR3925 replace WTR1625L on an iPhone 6 board?
Related products
339S00108 WiFi IC For iPad Air iPad Pro 9.7 Replacement
In stock
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
358S IC T211 Samsung Tab Charging IC – Tab 3 USB Charger IC
In stock



