PMI8940 Power IC – Qualcomm Charging PMIC for Mobile Repair
₨ 150
Qualcomm PMI8940 Companion PMIC for Board-Level Charging Repair
The PMI8940 power IC is a Qualcomm companion power management chip that pairs with Snapdragon 425, 427, 435, 450 and 625 platforms. It manages the battery charging side of the board, so a failed PMI8940 often shows up as a charging issue, a phone that refuses to take current, or a dead phone after a bad charger or water damage. Technicians stock this chip for IC change jobs on Qualcomm budget and mid-range boards. Check the marking on your board first, then replace it with hot air and a clean BGA rework routine to bring the charging circuit back.
PMI8940 Power IC: Qualcomm Charging PMIC for Snapdragon Boards
The PMI8940 power IC belongs to Qualcomm’s PMI89xx family of companion PMICs. These chips sit beside the main PMIC and the processor and take responsibility for the charging section of the board. Qualcomm’s own reference kernel source builds board configurations that pair the PMI8940 with the MSM8917, MSM8920, MSM8940, MSM8953 and SDM450 processors, which places this chip inside a large slice of the budget and mid-range Android phones that still reach Pakistani repair benches every day. On an MSM8917 design, the PMI8940 works next to the PM8937 main PMIC, and the platform software sets battery parameters such as float voltage and recharge threshold through it. When this chip fails, the phone loses its charging path, and no amount of software marna or charging port replacement fixes the fault. You need an IC change.
Where the PMI8940 Charging IC Fits in Your Repair Workflow
Most PMI8940 jobs start as a simple complaint: the phone does not charge, or it shows the charging icon with no real current. Your first steps stay the same as any charging repair. Check the cable, the port and the charging flex, then put the board on a DC power supply and watch the current draw. When the port and flex test fine and the current stays near zero, or the supply shows a short on the charging line, the fault moves to board level. A thermal camera or rosin smoke test then helps you confirm whether the PMI8940 charging IC heats up under power. Water damage, fake high-voltage chargers and drop impact all leave this chip vulnerable, so it deserves early attention in your diagnosis on Qualcomm boards from this era.
Matching the Right Qualcomm PMI8940 to Your Board
Always confirm the marking before you order. Qualcomm offers the same processors with several companion PMICs, and the reference kernel lists MSM8940 board variants built around PMI8937 and PMI8950 as well as PMI8940. Two phones with the same Snapdragon chip can carry different companion ICs, and the firmware expects the exact part the manufacturer designed in. Read the laser marking on the old chip under your microscope, or check the board schematic or boardview, and only proceed when it reads PMI8940. This simple check saves you from a wasted IC change and a board that still refuses to charge.
IC Change Process for the PMI8940 Power IC
The PMI8940 power IC sits on the board as a BGA-style package, so treat it as a proper rework job. Fix the board in a PCB holder, shield nearby plastic connectors and the underfill-sensitive processor area with heat-resistant tape, and apply quality flux around the chip. Use your hot air station with steady, even airflow and lift the old IC only when the solder fully melts, so you do not rip pads. Clean the pads with solder wick and flux, inspect every pad under the microscope, and repair any lifted pad before you continue. Prepare the new chip with your reballing kit and the correct stencil, align it carefully, and reflow until it self-centres. After the job, power the board through your DC supply first and confirm a normal charging current before you assemble the phone. A clean install restores the full charging function on the original board without a costly motherboard swap.
The PMI8940 sits naturally alongside the rest of your rework kit: a hot air station and soldering station for removal and install, a microscope for marking checks and pad inspection, reballing kits and stencils for the BGA work, and a regulated DC power supply for testing. For shops moving into heavier board repair, a preheater or BGA rework station gives you more control on multi-layer Qualcomm boards and reduces the risk to the processor next door.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Qualcomm PMI89xx companion PMIC for Snapdragon budget and mid-range platforms
- ✓Handles the battery charging side of the board’s power system
- ✓Pairs with the PM8937 main PMIC on MSM8917 designs
- ✓Covers MSM8917, MSM8920, MSM8940, MSM8953 and SDM450 reference platforms
- ✓Direct replacement where the board carries the PMI8940 marking
- ✓Restores a dead charging path without a motherboard swap
- ✓Suits standard hot air, flux and reballing rework workflows
- ✓A core stock item for Qualcomm charging repair benches
Specifications
| Brand | Qualcomm |
|---|---|
| Model | PMI8940 |
| Category | Power Management IC (Companion PMIC) |
| Compatibility | Qualcomm MSM8917, MSM8920, MSM8940, MSM8953 and SDM450 platforms |
| Technology | Qualcomm PMI89xx companion PMIC — battery charging management |
Common Repair Uses
- ✓Phone not charging after the port and flex test fine
- ✓Charging icon appears but the phone takes no real current
- ✓Short on the charging line traced to the companion PMIC
- ✓Charging circuit failure after a fake or high-voltage charger
- ✓Water-damaged boards with a corroded or failed PMI8940
- ✓Dead phone after drop damage cracks the IC’s solder joints
- ✓IC change instead of a full motherboard replacement
- ✓Donor-board IC transfer during board-level rework
Compatible Devices
- ✓Chipset-platform scope — verify the PMI8940 marking on your board before installation
- ✓Qualcomm MSM8917 (Snapdragon 425) boards
- ✓Qualcomm MSM8920 (Snapdragon 427) boards
- ✓Qualcomm MSM8940 (Snapdragon 435) boards with a PMI8940 companion PMIC
- ✓Qualcomm MSM8953 (Snapdragon 625) boards with a PMI8940 companion PMIC
- ✓Qualcomm SDM450 (Snapdragon 450) boards
- ✓MSM8917 designs pairing the PM8937 main PMIC with the PMI8940
- ✓Any Android board carrying the original PMI8940 marking
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can I replace a PMI8940 with a PMI8937 or PMI8950?
How do I confirm a PMI8940 fault before an IC change?
Related products
358S IC T211 Samsung Tab Charging IC – Tab 3 USB Charger IC
In stock
U2 Charging iPhone 8, iPhone 8 Plus, iPhone X Chip – 1612A1
In stock



