i2C Syn14 18in1 Silicone Middle Layer Platform iPhone X-14PM
₨ 1
i2C Syn14 Middle Layer Reballing Platform for iPhone X-14 Pro Max
The i2C Syn14 18in1 Universal Silicone Middle Layer Platform For iPhone X-14PM brings tin planting for 18 iPhone sandwich-board positions onto one fixture. It covers iPhone X, XS, XS Max and the full 11, 12, 13 and 14 series, including mini, Plus, Pro and Pro Max variants. The silicone body holds the middle layer in a fixed position under the stencil, so you get even ball height and fewer bridged joints. Reach for it when a dropped iPhone shows no service, a boot loop issue, or a dead phone traced to cracked interposer joints.
Out of stock
iPhone Middle Layer Reballing Platform for X to 14 Pro Max Sandwich Boards
The i2C Syn14 18in1 Universal Silicone Middle Layer Platform For iPhone X-14PM gives you one fixture for tin planting across 18 iPhone sandwich-board positions, from iPhone X up to iPhone 14 Pro Max. Apple moved to a stacked logic board with iPhone X, joining an upper and lower board through a middle layer (interposer frame) that carries hundreds of BGA solder joints. When those joints crack after a drop, board flex, or repeated heat stress, the phone comes to your bench with a network issue, a boot loop issue, or as a dead phone with no obvious short. This iPhone middle layer reballing platform holds the separated layer at a fixed, repeatable position so you can rebuild the joint array with consistent ball height and send the board back together with confidence.
Why the Middle Layer Needs a Dedicated Fixture
Interposer reballing behaves differently from standard IC reballing. The frame is long, thin and open in the center, so it shifts under hot air airflow and lifts away from the stencil the moment the paste starts to flow. Free-hand stencil work on a loose frame produces bridged balls, empty pads and uneven ball height, and a board rejoined on that base often fails again within days. The i2C Syn14 locates each board model in its own dedicated position, so the frame sits square under the stencil every time. You get the same alignment on the tenth job as on the first, you cut the time spent clearing bridges, and you reduce the risk of tearing pads during a second attempt. For a shop handling sandwich-board faults every week, that repeatability decides whether the job takes one hour or three.
Silicone Construction and 18-in-1 iPhone Coverage
i2C builds the Syn14 as a universal silicone platform rather than a single-model holder. One fixture covers the full stacked-board range from iPhone X to iPhone 14 Pro Max, including iPhone XS and XS Max, the 11 series, and the standard, mini, Plus, Pro and Pro Max variants of the 12, 13 and 14 series. That 18-in-1 layout replaces a drawer full of separate model holders and keeps the right position within reach when an unfamiliar board lands on your bench. The universal design follows a modular approach, so the platform stays relevant as your workload moves toward newer iPhone generations. iPhone XR does not use a stacked board, so it falls outside the scope of a middle layer fixture by design.
Using the iPhone Middle Layer Reballing Platform in Your Workflow
A typical middle layer job runs through five stages. First, you separate the sandwich board on a preheater or separation platform and lift the upper board with controlled hot air. Second, you clear old solder from both board pads and the interposer with flux and wick from your soldering station. Third, you seat the layer in its matching Syn14 position, lay the correct stencil on top and spread solder paste. Fourth, you reflow with your hot air station at a temperature that suits the paste. Fifth, you inspect every ball under a microscope before rejoining the boards. The Syn14 controls stages three and four, where most alignment errors begin.
Complete the bench with middle layer stencils from our Reballing Kits range, since stencil thickness and hole pattern must match each board generation. A stable hot air station, a fine-tip soldering station and a stereo microscope cover heating, pad prep and inspection, while a PCB holder keeps the full board steady during separation and reassembly. Once sandwich repairs become daily work, a dedicated separation and preheating station is the natural upgrade, bringing the same level of control to separation that the Syn14 brings to tin planting.
| Weight | 0.7 kg |
|---|
Key Features
- ✓18-in-1 layout covering every stacked-board iPhone from X to 14 Pro Max
- ✓Dedicated position for each board model for repeatable stencil alignment
- ✓Silicone construction for a stable, even bed under the middle layer
- ✓Universal design that replaces multiple single-model holders
- ✓Modular approach that keeps the platform useful as your bench grows
- ✓Holds the thin interposer frame steady during hot air reflow
- ✓Supports consistent ball height and fewer bridged joints
- ✓Built for daily sandwich-board work in professional repair shops
Specifications
| Brand | i2C |
|---|---|
| Model | Syn14 |
| Category | Middle Layer Reballing Platform |
| Compatibility | iPhone X to iPhone 14 Pro Max |
| Supported Devices | 18 iPhone stacked-board positions (18-in-1) |
| Technology | Middle layer BGA tin planting / reballing |
| Material | Silicone |
Common Repair Uses
- ✓Middle layer reballing and sandwich-board rejoin work
- ✓Reballing the interposer frame after sandwich-board separation
- ✓No service or network issue caused by cracked middle layer joints after a drop
- ✓Boot loop issue traced to an open interposer connection
- ✓Dead phone with no short where the fault sits between the two boards
- ✓Wi-Fi or Bluetooth faults linked to lifted joints between board layers
- ✓Rebuilding joints on interposer pads after liquid damage cleaning
- ✓Re-tinning a middle layer after a failed first rejoin attempt
- ✓Restoring joints weakened by board flex in bent iPhone frames
Compatible Devices
- ✓Stacked (sandwich) logic boards from iPhone X to iPhone 14 Pro Max
- ✓iPhone X
- ✓iPhone XS and iPhone XS Max
- ✓iPhone 11, 11 Pro and 11 Pro Max
- ✓iPhone 12 and iPhone 12 mini
- ✓iPhone 12 Pro and iPhone 12 Pro Max
- ✓iPhone 13 and iPhone 13 mini
- ✓iPhone 13 Pro and iPhone 13 Pro Max
- ✓iPhone 14, 14 Plus, 14 Pro and 14 Pro Max
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which solder paste works best for iPhone middle layer reballing?
How do you separate an iPhone sandwich board before middle layer reballing?
Related products
QUICK 857 Pro Rework station (European plug)
In stock
RF4 RF-530 Spray – Electronic Cleaning Spray for Mobile PCB Repair
In stock
SUNSHINE SS-5120 128 in 1 Precision Screwdriver Set for Mobile Repair
In stock
SUNSHINE SS-890B Mini Laser Machine for iPhone Back Glass & Screen Bracket Removal
In stock



