PM8350C 004 Power IC for Mobile Repair Pakistan
₨ 350
PM8350C Power IC for Board-Level Power Repair
The PM8350C is a Qualcomm power management IC built for SPMI-based designs. It supplies regulated rails from one chip and carries GPIO, PWM, flash LED, and thermal monitoring blocks. Technicians use it when a dead phone, charging issue, or boot loop points to the power tree. Match the part marking on your donor board before you order, then verify rails before you power the board up.
PM8350C Power IC for Mobile Repair Technicians
The PM8350C power IC is a Qualcomm power management chip that generates regulated rails across the board. When a phone stays dead or refuses to charge, this PMIC sits near the top of your checklist, because a failed rail stops the entire boot chain. Your repair bench needs a part you can identify, test, and install with confidence. This listing explains what the PM8350C does, where it fits in the power tree, and how to confirm a fault before you replace it.
Where the PM8350C Fits in the Power Tree
Qualcomm designs the PM8350C to work inside a multi-PMIC layout on SPMI-based platforms. Linux device-tree support lists it alongside companion PMICs such as PMK8350 and PMR735A on the sc7280 platform. Its regulator set includes ten switching regulators, thirteen LDOs, and one BOB regulator, which means each rail on your schematic should trace back to a specific output. Open the power tree on your board schematic and map every missing rail to its regulator before you blame the IC. That mapping saves time and prevents unnecessary IC changes.
Diagnosing a PM8350C Fault Before Replacement
A failed PMIC rarely fails alone, so start with the battery connector, the charging path, and any short-to-ground condition. Use a bench power supply with current limiting to locate a shorted rail without damaging nearby components. Measure rail voltages at the test points defined on your schematic, and compare each reading against the expected value for that rail. If the rails come up but the phone still hangs on the logo, check the processor and memory before you remove the power IC. A cracked joint or a board flex fault can mimic a PMIC failure, so inspect the solder under magnification first. Many technicians call this step the real diagnosis, and it prevents an unnecessary IC change karna job.
Replacement Workflow and Board Checks
Confirm the marking and package of the old IC against your replacement before you order it. Remove the faulty part with controlled hot air, then clean the pads with fresh flux and solder wick. Set the new IC on the pads, align it under magnification, and reflow it with a steady temperature profile. Avoid lifting pads, because a damaged pad turns a simple swap into a board-level rework. After soldering, measure every rail again before you apply full power. Record your rail readings for each job, since those numbers help you spot patterns across similar boards.
| Weight | 0.1 kg |
|---|
Key Features
- ✓SPMI-interfaced Qualcomm power management IC
- ✓10 SMPS switching regulators
- ✓13 LDO regulators
- ✓1 BOB regulator
- ✓GPIO block with nine GPIO lines for the PMIC
- ✓PWM output support for backlight and LED control
- ✓Flash LED driver support
- ✓Thermal alarm monitoring support
Specifications
| Brand | Qualcomm |
|---|---|
| Model | PM8350C |
| Category | Power Management IC (PMIC) |
| Compatibility | Qualcomm sc7280 platform device-tree support |
| Technology | SPMI-interfaced PMIC with 10 SMPS, 13 LDO, and 1 BOB regulator |
Common Repair Uses
- ✓Dead phone diagnosis when one or more power rails fail to come up
- ✓Charging issue repair when the charge indicator stays off
- ✓Boot loop investigation after a suspected power sequencing fault
- ✓Hang on logo troubleshooting when rail voltages drop under load
- ✓PMIC replacement after isolating a shorted rail with current-limited power
- ✓Flash LED and backlight rail faults traced to the PMIC PWM or LED outputs
- ✓Thermal alarm checks during overheating or hot spot repairs
- ✓BGA reflow and reballing work on a PMIC during board-level rework
Compatible Devices
- ✓Qualcomm sc7280 platform designs with PM8350C device-tree support
- ✓Qualcomm sc7280 platform boards that list PM8350C in Linux device-tree files
- ✓Multi-PMIC designs that pair PM8350C with PMK8350 and PMR735A
- ✓SPMI-based Qualcomm power architectures using 10 SMPS, 13 LDO, and 1 BOB regulator layouts
- ✓Donor boards where the marking matches the PM8350C part number
- ✓Board-level replacement only after confirming the schematic power tree
- ✓Device-specific fitment must be verified against the donor board before installation
- ✓Not a universal drop-in part across all Qualcomm PMICs
- ✓Verify pin count and package against the original IC on your board
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which bus does the PM8350C use to communicate with the processor?
How many regulators does the PM8350C provide?
Related products
339S0223 For iPad 5/Air1 A1474 Wifi IC – U5800 WiFi Module
In stock



