MT6315 Power IC – 4-Phase Buck PMIC for Mobile Repair
₨ 400
MT6315 Power IC for Mobile Repair Boards
The MT6315 is a MediaTek power management IC with four buck regulator outputs. Its outputs can be combined through eFuse settings, and it is configured over SPMI. The IC is a step-down regulator with a 6V maximum input and a programmable output range from 0.4V to 1.19375V, rated for up to 5A. It comes in a compact 45-pin WLCSP package measuring 2.35 × 3.44 mm, and it operates between -30°C and 85°C. This listing covers the MT6315 family. The exact variant specifications for the SP suffix are not confirmed in this listing.
MT6315 Power IC: Four-Phase Buck Regulator for Board-Level Repair
The MT6315 belongs to MediaTek’s power management IC family. It is a step-down DC/DC regulator that works with the SPMI bus. Four buck outputs sit inside one package, and eFuse settings can combine them. For a repair technician, that means the IC supplies several power rails from one chip, so a fault in its power section affects more than one rail. Before you remove a suspect IC, confirm the rail behavior on your board.
Electrical Characteristics
The datasheet data available for the MT6315GP/B variant lists a 6V maximum input and a maximum output of 1.19375V. The output starts at 0.4V. The current rating is 5A. The device is marked as a synchronous rectifier No, which means it is a non-synchronous step-down design. Check these values against your board schematic before replacement, because the SP suffix values have not been verified in this listing.
Package and Operating Range
The package is 45-pin WLCSP (UFBGA), measuring 2.35 × 3.44 mm, and it is surface mount. The operating temperature is -30°C to 85°C. Because the package is this small, reballing and replacement need a stable hot air setup and a microscope for alignment.
Where This IC Fits in Your Workflow
Use this IC when a board’s power rail check points to the MT6315 family. Measure the rails with a multimeter before you order a replacement. If the rail is shorted or missing, replace the IC after you confirm the fault is in the IC and not in a downstream component.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Four buck outputs in one IC
- ✓Outputs can combine through eFuse settings
- ✓SPMI configurable
- ✓Step-down regulator with 6V input
- ✓45-pin WLCSP package, 2.35 × 3.44 mm
- ✓Operating range -30°C to 85°C
Specifications
| Brand | MediaTek |
|---|---|
| Model | MT6315 (family; GP/B variant data) |
| Category | Power ICs |
| Technology | 4-phase buck regulator, SPMI configurable |
| Package | 45-WLCSP (2.35 × 3.44 mm) |
| Input Voltage | 6V maximum |
| Output Voltage | 0.4V to 1.19375V |
| Power Rating | 5A |
| Operating Temperature | -30°C to 85°C |
Common Repair Uses
- ✓Replacing a faulty MT6315-family IC on a board
- ✓Testing the buck output rails on a power section
- ✓Reballing and reflowing the WLCSP package with hot air
Compatible Devices
- ✓MT6315 family PMIC, chipset-level scope. Not device-specific. Confirm the exact marking on the removed IC before replacement.
- ✓MT6315 family PMIC (chipset-level scope)
- ✓Not device-specific; verify against your board marking
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the input voltage limit of the MT6315?
What is the package size of the MT6315?
Related products
A3B U2 610A3B Charging Power IC iPhone 7,7+ Tristar U4001
In stock
PM8916 Power Control IC – Qualcomm PMIC for MSM8916 Boards
In stock



