PMI8994 Power IC for MSM8996 Mobile Repair

₨ 200

PMI8994 Power IC for MSM8996 Boards

The PMI8994 power IC is a Qualcomm power management chip that communicates over the SPMI bus. It is commonly found on MSM8996-based boards, where it supplies power to several LDO rails. The chip also includes GPIO, MPP, LPG, and WLED blocks, so a single faulty part can stop more than one subsystem. This listing gives you a clear reference for the part, its role on the board, and a practical approach to rail diagnosis and replacement. Use it when you need to confirm power behavior before ordering a replacement or planning hot air rework on a Snapdragon 820-class device.

20 People watching this product now!
Description

PMI8994 Power IC and Its Role in MSM8996 Power Delivery

The PMI8994 power IC sits alongside the primary PMIC on MSM8996 designs and feeds several regulator outputs that the board depends on. When a secondary rail never comes up while the main PMIC looks healthy, this chip belongs on your suspect list. Understanding what it controls saves you hours of random probing and part swapping at your repair bench. The sections below cover where the chip fits in the power tree, which functional blocks you should test, and how to decide between a repair and a replacement.

Where the PMI8994 Fits in the Power Tree

The PMI8994 connects to the processor platform through the SPMI interface, which Qualcomm designs use to control power management blocks over a shared serial bus. Its place in the device tree shows it as a separate SPMI device with its own regulator, GPIO, MPP, LPG, and WLED functions. On MSM8996 boards, the regulator outputs from this chip feed LDOs that the primary PMIC relies on, so a fault here can appear as a rail that stays dead while the main PMIC shows normal activity. Your board schematic tells you exactly which rails originate from this IC and which come straight from the primary PMIC. Confirm those rail names on your specific board before you condemn the component. A clear map of the power tree turns a vague dead-board symptom into a focused test plan.

Built-In Blocks You Should Test

Beyond the regulators, the chip contains GPIO and MPP pin blocks that handle signal lines routed to peripherals on the board. It also integrates an LPG, which is a lighting pulse generator, and a WLED driver. These blocks matter when a display backlight or notification LED fails on a board that uses these functions, so a backlight complaint does not always point to the display itself. The regulator section includes supply inputs for rails named S1, S2, S3, and L1 in the Linux kernel bindings, which lets you match your schematic against those labels. Test in a fixed order: check the input supply first, then the output rail, then the enable path. This sequence tells you whether the fault sits upstream of the IC or inside it. Record each reading against the schematic value so you can compare boards from the same family later.

Bench Diagnosis and Replacement Decisions

Start with a multimeter check on each rail and compare every reading against the schematic. If the input supply is present but the output rail is missing or shorted to ground, the IC or a nearby capacitor may have failed, and a short on a downstream load can also pull the rail down. Inspect the area under a microscope for lifted pads, cracked solder joints, or burned resin before you apply any heat. Disconnect or isolate loads where your board layout allows it, so you can see whether the shorted rail clears. When you replace the IC, use a hot air station with controlled temperature and a flux suited to your process, and confirm the board revision before you order the part. Reflow the chip carefully and avoid overheating the surrounding components. Power the board from a bench supply with current limiting before you reinstall it in the housing. A new chip will fail again if a downstream load still draws excess current, so clear that fault first.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Qualcomm SPMI-interfaced power management architecture
  • Integrated regulator outputs for MSM8996 board power rails
  • Built-in GPIO and MPP pin blocks
  • Integrated LPG (lighting pulse generator) block
  • Integrated WLED driver block
  • Reference platform support on Dragonboard 820c
  • Suited to board-level rail diagnosis and IC-level replacement
  • Pairs with the primary PMIC in MSM8996 power delivery

Specifications

BrandQualcomm
ModelPMI8994
CategoryPower Management IC
CompatibilityMSM8996 platform
TechnologySPMI-interfaced power management IC

Common Repair Uses

  • Tracing dead secondary rails on MSM8996 boards with a multimeter
  • Diagnosing boards where LDO outputs fed by this IC stay low while the main PMIC looks normal
  • Checking backlight and LED fault paths tied to the integrated WLED and LPG blocks
  • Testing GPIO and MPP lines when a peripheral fails to respond
  • Replacing a confirmed faulty IC with hot air rework after microscope inspection
  • Bench-testing a replacement chip on a development board before board-level installation

Compatible Devices

  • Verified at chipset-family and reference-board level
  • MSM8996-based mobile platforms (Snapdragon 820 class)
  • Qualcomm Dragonboard 820c development board
  • Boards pairing the PMI8994 with the primary PMIC in MSM8996 power designs
  • Qualcomm SPMI-bus power management designs

FAQ

What is the product name?
The product name is PMI8994 Power IC.
What is the brand of this product?
The brand of this product is Qualcomm.
What is the model of this product?
The model of this product is PMI8994.
What is this product used for?
This product is used for supplying regulated power rails and driving peripheral functions on MSM8996-based boards.
Which devices are compatible with this product?
This product is compatible with MSM8996-based platforms, including the Dragonboard 820c development board.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which Snapdragon platform uses the PMI8994?
The PMI8994 is commonly found on MSM8996-based devices, where it supplies power to several LDOs on the primary PMIC.
Does the PMI8994 include a backlight driver?
Yes, the PMI8994 includes a WLED block, which handles LED and backlight driving on boards that route those functions through it.